海洋平台双相不锈钢管线的焊接

就双相不锈钢的特异性能．介绍双相不锈钢管线的焊接特点与技术。     

铍铜电极在接触类焊机上的应用研究

接触焊用电极材料是接触类焊机的核心部件，要求具有优良的导电率，强度和高的耐高温性能（软化温度）等综合性能，本项目采用含铍多元铜合金，利用含铍铜合金具有较高的硬度，耐高温性能，强度和导电率的综合性能，研制出一种达到进口电极性能要求的长寿命新型电极材料，通过在进口及国产设备使用完全满足要求，解决了国产焊接电极长期存在的焊接质量差，寿命短的问题。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

唐钢ER70S-6焊丝钢的生产工艺研究及质量分析

介绍了唐钢ER70S-6焊丝钢的特点，对盘条质量进行了分析。对该钢化学成分、冶炼和轧制工艺进行了优化研究，使其综合性能明显改善。     

X-Ray Measurement of Residual Stress in Plastic Bonded Explosives

The X-ray diffractive technology was adopted for tentative study of plastic bonded explosive. The datum of some new diffractive peaks in standard PDF cards were added. The effects of strain to interplanar distance and crystal size of the explosive were studied. The results show that grain size of plastic bonded explosive is decreasing with the increasing of the pressure, and the residual stress of the explosive is draw stress.     

76 mm口径EFP成形过程数值模拟及影响因素研究

采用LS-DYNA3D对76mm口径药型罩爆炸成型弹丸(EFP)的成形过程进行了数值模拟，模拟结果与实验数据基本吻合．通过数值模拟着重分析了装药长径比L／D、壳体厚度、药型罩壁厚对EFP速度的影响规律，得到了有关EFP成形速度公式，得出EFP速度随L／D的增大而增大，随药型罩厚度增大而减小，受装药外壳厚度影响不大．     

钻机绞车滚筒体的窄间隙埋弧焊

针对钻机绞车滚筒体采用手工电弧焊工人劳动强度大、焊接效率低、质量不稳定及返修率高等问题,研制了钻机绞车滚筒体窄间隙埋弧焊专机。该专机由ESAB—A2埋弧焊电源和焊接小车、窄间隙焊头、滚轮架、防窜装置、旋转地线夹、三维焊接工作台、焊剂自动回收机组成。使用表明,采用该焊机焊接的滚筒体焊缝质量完全符合设计要求,合格率100%,焊接效率比原来提高6倍。每件滚筒体的焊接可降低人工成本约80%。     

特长办公大楼控制爆破拆除

介绍了一栋特别长的办公大楼定向控制爆破拆除,并对爆破参数、预拆除、爆破网路敷设及爆破效果等进行了分析论述。     

梯恩梯-吉纳、地恩梯-太安装药体系自旋爆轰特性的研究

本文研究了梯恩梯-吉纳(TNT-DINA)和地恩梯-太安(DNT-PETN)体系的自旋爆轰现象,爆轰波是以低频脉冲方式传播.这些体系具有的爆速、爆热分别为DJ=7.3～7.4km/s和Qv=(5.40±0.01)MJ/kg.不同组成的爆速和爆压PJ通过SW程序计算.用扩散区的爆压P3和爆温T3来评估爆轰波的衰减和重新点火.敏化剂含量相同,梯恩梯-黑索金(TNT-RDX)体系的爆压PJ大于TNT-DINA的爆压,TNT-RDX体系的温度T3比TNT-DINA高60～100K.计算值与实验结果吻合较好.     

框架结构焦仓的定向倒塌爆破

介绍了框架结构焦仓定向爆破拆除的设计与施工，着重介绍了爆破参烽的选取及安全防护措施。达到预期的爆破效果。