钨合金圆筒爆破试验破片分布的统计分析

采用圆筒爆破试验方法研究了易碎型钨合金的破片分布特征,并与93W合金的结果进行了对比.对破片的数量和质量分布特征进行了统计分析,发现易碎型钨合金的破片率明显高于93W合金,而且破片的均匀性也明显好于93W合金,但易碎钨合金的破片回收率低于93W合金,而且受装药量的影响较大.     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

NiTi形状记忆薄膜的显微结构和力学性能

NiTi形状记忆合金薄膜具有形状记忆效应，极有希望用于制造高技术领域微电子机械系统中的微型激发器。NiTi形状记忆合金薄膜在制备和使用过程中需要高品质（衬）底材。本文利用高分辨电子显微学和高分辨分析电子显微学详细研究了硅底材NiTi形状记忆合金薄膜的NiTi／Si和NiTi／SiO2微结构体系，包括薄膜精细结构和界面反应。也研究了其显微结构和力学性能的关系。特别给出了NiTi形状记忆合金薄膜产生疲劳过程的微观过程的起因，通过高达十万个使用热循环前后样品显微结构变化的比较，发现纳米尺度上的TiNi3新相的形成导致疲劳过程的发生。如何抑制TiNi3新相形成的研究正在进行之中，这将为进一步提高NiTi形状记忆合金的使用寿命指出方向。     

微晶合金在电流互感器中的应用

从微晶合金的性能特点出发，分析了其在电流互感器中的应用前景。     

PDB-18C6对TI(Ⅰ),An(Ⅲ),Cu(Ⅱ)的吸附及从α轰击的金靶中分离~(199)TI

本文研究了用冠醚树脂二苯并-18-冠-6甲醛聚合物(简称PDB-18C6)对T1(Ⅰ),Au(Ⅲ),Cu(Ⅱ)的吸附行为。实验表明,在盐酸溶液中冠醚树脂的吸附效率顺序为Au(Ⅲ)>T1(Ⅰ)>Cu(Ⅱ)。用高氯酸和乙二醇乙醚淋洗T1(Ⅰ),Au(Ⅲ),它们的回收率一般在82-98.9％和98-100％。还在1.2m回旋加速器的外靶装置上,用25-27MeV的α粒子轰击金靶,累计束流强度为27μA·h,经处理分离后得到仅含0.50％~(200)T1的较高纯度的~(199)T1。     

TiAl基合金板材制备技术的发展现状

综述了TiAl基合金板材制备技术的发展现状。介绍了的制备TiAl基合金板材三种技术的工艺过程及制得的TiAl基合金板材的显微组织和力学性能。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

Semiparametric Estimation in Time‐Series Regression with Long‐Range Dependence

Abstract. We consider semiparametric estimation in time‐series regression in the presence of long‐range dependence in both the errors and the stochastic regressors. A central limit theorem is established for a class of semiparametric frequency domain‐weighted least squares estimates, which includes both narrow‐band ordinary least squares and narrow‐band generalized least squares as special cases. The estimates are semiparametric in the sense that focus is on the neighbourhood of the origin, and only periodogram ordinates in a degenerating band around the origin are used. This setting differs from earlier studies on time‐series regression with long‐range dependence, where a fully parametric approach has been employed. The generalized least squares estimate is infeasible when the degree of long‐range dependence is unknown and must be estimated in an initial step. In that case, we show that a feasible estimate which has the same asymptotic properties as the infeasible estimate, exists. By Monte Carlo simulation, we evaluate the finite‐sample performance of the generalized least squares estimate and the feasible estimate.