Top illuminated organic photodetectors with dielectric/metal/dielectric transparent anode

The top illuminated organic photodetectors (OPDs) with a Dielectric/Metal/Dielectric (DMD) transparent anode are fabricated. The transparent electrode is composed of molybdenum trioxide (MoO₃)/silver (Ag)/MoO₃ layers and zinc oxide (ZnO)/aluminum (Al) is used for bottom cathode. The optimized DMD electrode has an optical transmittance of 85.7% at the wavelength of 546 nm and sheet resistance of ∼6 Ω/sq. The fabricated OPDs exhibit a high detectivity and wide range linearity.     

不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。     

Crystal violet dye sorption and transport in/through biobased PVA cryogel membranes

Cryogels based on poly(vinyl alcohol) [PVA] and three types of bioinsertions such as scleroglucan, cellulose microfibers, and zein, respectively, have been prepared using capacity of PVA to crosslink by repeated freezing–thawing cycles. The effect of the incorporation of biopolymers on the properties of PVA cryogel has been studied by using several techniques such as: scanning electron microscopy, differential scanning calorimetry, and Fourier transform infrared studies. The obtained biobased cryogel membranes were subjected to sorption and to diffusion experiments using Crystal Violet (CV), a dye commonly used in the textile industry and in medicine. Image analysis with CIELAB system was used both to monitor the cryogels loading with CV and to gain insight in the dye state into the gel, in correlation with the bioinsertion type and gels morphology. Dye diffusion but also sorption capacity of the cryogels was found to be closely related to the type of biopolymer. In this article the equilibrium (sorption isotherms) and transport properties (diffusion and permeability coefficients) of CV, in/through physical cross‐linked PVA hydrogel membranes with bioinsertions has been reported. The highest efficiency for the CV removal from aqueous solutions was obtained for the PVA/Scl cryogels. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41838.     

多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。     

In2O3:Ga and In2O3:P-based one-electrode gas sensors: Comparative study

Gas sensing characteristics of one-electrode sensors based on the In₂O₃ ceramics doped by gallium and phosphorus have been discussed. In₂O₃-based ceramic was prepared by sol–gel technology. Ozone, CO, CH₄ and H₂ were used as tested gases. The doping concentration effect on the sensor parameters such as magnitude of response, operating temperature, response and recovery times, sensitivity to the air humidity, and selectivity have been analyzed. It was shown that In₂O₃ doping by Ga and P could be used for the sensor performance optimization. It was assumed that the appearance of the second phase (InPO₄ and Ga₂O₃) and the change of structural parameters, taking place during doping process, were the main factors controlling the change of operating characteristics in In₂O₃:P and In₂O₃:Ga-based sensors.     

The formation of fibrous structure of polyamide 6 induced by the three-step forming process and its prominent reinforcement in nitrile rubber

Nitrile rubber (NBR) blends with excellent performance have always been a hot research topic in petroleum field. Due to the excellent performance and compatibility of polyamide 6 (PA6), it provides an opportunity for the preparation of high-performance NBR/PA6 blends. In this article, NBR/PA6 blends were prepared by the three-step molding process. Experimentally, it was found that PA6 has a prominent reinforcement effect in NBR matrix. The variation of this mechanical property was investigated from different aspects of the crystal structure, crystallinities, phase morphology, and so on. It can be cleared that the formation of fibrous structure of PA6 phase is the main factor for reinforcement of the polymer blends. Meanwhile, the formation mechanism of the special phase structure induced by the three-step process is deeply expounded and its structural evolution schematic is established. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47472.     

Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.