多层薄膜结构气敏效应研究

在SnO2气敏薄膜层上覆盖一层或多层钝化材料（SiO2,Al2O3) 薄膜，制成的多层膜气敏元件，可很好地排除大分子气体如乙醇等对小分子H2检测的干扰，使其具有单独检测H2的功能。本文还通过测量元件的升温曲线，推导出敏感体表面的氧吸附活化能；找出活化能与灵敏度、选择性的关系。根据实验现象和物性分析结果，试着探讨了元件的敏感机理。     

共晶碳化物团球化对铸铁激光熔敷层抗裂性的影响

为提高铸铁表面大面积激光熔敷层抗裂性问题，通过冶金因元素控制熔敷层组织形态在熔敷材料中加入碱金属元素钾，研究了在激光快速加热条件下钾对铸铁激光熔敷层组织团球化的影响，进而分析了该球状组织对熔敷层抗裂性的影响，结果表明随熔敷金属内钾含量增多熔敷层内共晶碳化物组织呈球状及孤岛状，这种组织明显提高了熔敷层抗裂性，此外大量的渗碳体组织确保了熔敷层具有较高的耐磨性；获得了无裂纹的大面积搭接熔敷层，其对应合金系统为Fe-C-Si-Ni-K。     

用菱锌矿制取轻质氧化锌的研究

介绍了以菱锌矿为原料生产轻质氧化锌的方法，论述了反应酸浓度，煅烧温度，溶液PH值对实验的影响，并对生产工艺条件进行了研究。其工艺流程是将粉碎后的菱锌矿进行循环酸浸，净化后再直接和碳化母液反应，经沉降后再煅烧分解为轻质氧化锌，产品质量符合国家标准，视比容大，活性强，成本低，经济效益显著。     

The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

高铬锰白口铸铁的软化处理

研究了 4种退火工艺对高铬锰白口铸铁组织和硬度的影响规律。结果表明 ,采用 85 0℃保温 4h ,随后于 72 0℃保温 6h退火工艺 ,硬度最低为 36～ 38HRC ,机加工性能最好。     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

首钢烧结配加扬地粉试验研究

介绍了首钢原料条件下配加扬地粉对烧结生产影响的实验室研究.随着扬地粉配入量的增加,烧结矿转鼓强度、成品率改善,燃耗有少量上升,利用系数增加,低温还原粉化指数变差.研究结果表明:在首钢目前条件下,配入10%～20%的扬地粉是可行的.二烧车间进行了扬地粉工业试验,其最高配比达到30%,工业试验时烧结各项指标变化与实验室试验结果基本一致.     

熔融碳酸盐燃料电池阴极材料的导电性

通过交流阻抗方法研究了熔融碳酸盐燃料电池阴极材料锂镍氧化物、锂钴氧化物和锂铁氧化物的导电性能。结果表明:锂镍氧化物电极的导电性最好,锂钴氧化物电极的导电性次之,锂铁氧化物电极的导电性最差;它们的导电性都随着温度的升高而按指数规律增加;在合成锂钴氧化物(或锂铁氧化物)的过程中,使Li2CO3轻微过量,可以提高锂钴氧化物(或锂铁氧化物)电极的导电性,而且在同一温度下,随着nLi∶nCo(或nLi∶nFe,摩尔比)值的增大,锂钴氧化物(或锂铁氧化物)电极的导电性显著增加。     

Relating catalyst structure and composition to the water–gas shift activity of Cu–Zn-based mixed-oxide catalysts

In order to investigate the effect of cerium oxide on Cu–Zn-based mixed-oxide catalysts four catalyst samples were characterized by means of XRD, in situ XANES and thermogravimetric analysis. The activity of the catalyst samples was tested for the forward water–gas shift reaction. Cerium oxide was found to increase the crystallinity of the ZnO phase indicating a segregation of the Cu and ZnO phases. The TOF of the water–gas shift reaction based on chemisorption data was found to be independent of composition and preparation conditions of the four catalyst samples. In contrast, the catalyst stability depends on composition and preparation conditions. Cerium oxide impregnated before calcination of the hydrotalcite-based Cu–Zn precursors leads to a more stable water–gas shift catalyst.