甲基葡萄糖甙（MeG）水溶液工艺改进试验

介绍了用５次以上的母液生产ＭｅＧ水溶液工艺的改进试验。     

二铁取代硅钨酸盐光解引发甲基橙的脱色

合成了SiW10Fe2的季胺盐(Fe2POM),并对其结构进行了表征.以Fe2POM为催化剂,研究了甲基橙的起始浓度、催化剂添加量、不同pH值等因素对光脱色速率的影响.利用异丙醇作为·OH捕获剂,探讨了甲基橙在Fe2POM-H2O2体系中的光化学脱色规律和机制.结果表明:体系在较宽的pH范围内具有高的光脱色活性,40—160mg/L初始质量浓度范围内,甲基橙的脱色速率随初始浓度降低而升高,脱色过程符合表观一级反应动力学规律.各体系的光脱色活性依次为:Fe2POM-H2O2单纯的Fe2POM>单纯的光照.     

药物中间体2-[(2′-氰基联苯-4-基)甲基氨基]-3-硝苯甲酸乙酯的制备

本文介绍了以3-硝基-2-叔丁氧甲酰氨基苯甲酸乙酯为原料，在碱性条件下与4-(2-氰基苯基)-1-溴甲苯发生亲核取代反应制备2-[(2′-氰基联苯-4-基)甲基氨基]-3-硝苯甲酸乙酯的方法，产品经核磁共振验证其结构，产品收率达83％。本合成工艺条件温和，适合工业化生产。     

一步法合成5-甲基海因

以氰化钠、碳酸铵、乙醛等为原料，常压下一步反应得到５甲基海因，总收率７０２％。其最佳操作条件为：反应温度７５℃，反应时间３ｈ，原料碳酸铵与氰化钠之比为２∶１，酸化回流ｐＨ值为２，酸化回流时间２ｈ。     

A rapid test to measure performance,emission and wear of a diesel engine fueled with palm oil diesel

Results of performance, emission and tribological evaluations of palm oil methyl ester and its blends with conventional diesel in an automobile diesel engine test bed are presented. Polymerization and carbon deposits on the fuel injector were monitored. CO, CO₂, O₂, combustion efficiency and temperature of exhaust gases were also measured. Palm oil methyl ester and its blends have great potential as alternative diesel fuel. Performance and exhaust gas emission for palm oil methyl ester and its blends with conventional diesel are comparable with those of conventional diesel fuel. Palm oil methyl ester does not pose a severe environmental problem and will not deteriorate engine and bearing components.     

Surface morphology control of immiscible polymer-blend thin films

The effects of the molecular weights (molecular weight of polystyrene, M_w,PS, varying from 2.9 to 129 k) on the surface morphologies of spin-coated and annealed polystyrene/poly (methyl methacrylate) (PS/PMMA=50/50, w/w) blend films were investigated by atomic force microscopy and X-ray photoelectron spectroscopy. For the spin-coated films, when the M_w,PS varied from 2.9 to 129 k, three different kinds of surface morphologies (a nanophase-separated morphology, a PMMA cellular or network-like morphology whose meshes filled with PS, a sea-island like morphology) were observed and their formation mechanisms are discussed, respectively. Upon annealing, two different morphology-evolution processes were observed. It is found that a upper PS-rich phase layer is formed when M_w,PS<4 k, and this behavior is mainly attributed to the low interfacial tension between PS and PMMA component. When M_w,PS>4 k, the PS-rich phase forms droplets on top of the PMMA-rich phase layer which wets the SiO_x substrate. These results indicate that the surface morphology of the polymer blend films can be controlled by the polymer molecular weight and annealing conditions.     

聚甲基丙烯酸甲酯／纳米SiO2复合粒子的制备与表征

采用甲基丙烯酸-3-甲氧基硅丙酯（MPs）对分散于甲基丙烯酸甲酯（MMA）中的纳米SiO2粒子进行偶联改性，得到了表面改性的纳米SiO2单体分散液，用原位悬浮聚合方法制备了不同SiO2含量的PMMA／纳米SiO2复合粒子。通过红外光谱、透射电镜、差示扫描量热分析和热重分析等方法对制备的纳米复合粒子进行了表征，结果表明，纳米SiO2粒子在PMMA中分散良好；MMA可通过与MPS的共聚而有效地接枝到SiO2粒子表面，当SiO2含量为6．6％（质量分数，下同）、MPS用量为0．06g／gSiO2时，其接枝率可达73．8％；同时，纳米SiO2的引入可提高PMMA的耐热性能，当Si02含量为14.7％时，其玻璃化转变温度和最大热分解速率时的温度分别提高了11．8℃和18．8℃。     

改性SBS胶粘剂的研制

以丙烯酸酯类混合单体对SBS热塑性弹性体在混合溶剂中接枝共聚，添加混合型增粘树脂，研制成接枝改性的SBS胶粘剂，具有较高的初粘力和终强度。探讨了单体比例、引发剂用量、反应温度、反应时间、增粘树脂对胶液性能的影响。     

压力条件下淀粉合成甲基葡萄糖苷

以淀粉、甲醇为原料 ,以酸为催化剂 ,在压力条件下合成甲基葡萄糖苷 (简称甲苷 ) ,得出最佳催化剂是浓硫酸。通过正交实验 ,考察了糖醇比、反应压力、催化剂用量及反应时间对合成甲苷的影响 ,得到合成甲苷的最佳条件为n(淀粉 )∶n(甲醇 ) =1∶30 ,压力 0 5MPa ,催化剂用量为淀粉质量的 5 % ,反应时间 12 0min ,收率达 98 9%。     

新型热管反应器在轻烃醚化中的研究及应用

将热管技术与催化反应器结合,构建了蛇形回路热管反应器。利用该反应器,进行了轻烃醚化工业侧线试验,考察了进料温度、液相体积空速、冷却水流量、进料浓度对反应结果的影响;测定了催化床层的轴向温度分布。利用反应器数学模型并结合试验数据,采用下山单纯形最优化方法获得了床层对热管的传热膜系数准数关联方程。所开发的新型热管反应器在2万t/a甲基叔丁基醚(MTBE)生产装置的扩能改造中应用成功。