Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

Dynamic response and behavior of reinforced concrete slabs under impact loading

Reinforced concrete slabs are among the most common structural elements. In spite of the large number of slabs designed and built, the effect of their details on their behavior under impact loads are not always appreciated or properly taken into account. This experimental study was aimed at understanding the dynamic behavior of structural concrete slabs under impact loading to improve the state of the art of protective design. This study investigated the effects of different types of slab reinforcements and the applied impact loads on the dynamic response and behavior of reinforced concrete slabs.     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

碳纤维复合材料柔性连续抽油杆开发及应用

碳纤维柔性连续抽油杆选用高性能碳纤维 ,以环氧树脂胶液为基体材料 ,添加一定配比的固化剂、促进剂和脱模剂 ,采用拉挤成型工艺制成 ,其开发的关键技术是连续成型、连接接头和安全保险装置。现场应用试验表明 ,TXC— 1、TXC— 2、TXC— 3三种规格的碳纤维柔性连续抽油杆能可靠应用于泵挂深度分别为 12 0 0、 180 0、 30 0 0m的直井和斜井中 ,实测比钢抽油杆节电 ,日产油量提高 。节能增产效果显著。     

实炉底节能连续式加热炉

轧钢生产使用实炉底连续式加热炉加热钢坯，炉内双纵滑管用耐热耐高温材料，无水冷，起到节约水、电的作用，达到节能增效的目的。     

连轧管“竹节”问题的研究

本文就各工艺参数对“竹节”的影响进行了较系统的试验。在此基础上，对连轧管“竹节”问题进行了分析，得出了“竹节”形态的基本特征；后“竹节”与轧制压力的关系；影响后“竹节”的主要工艺因素等一系列有意义的结果。对前、后“竹节”形态明显不同的原因进行了初步探讨。提出了“竹节”在线控制模型的初步设想。     

Equipment for Testing Sheet Structural Materials under Biaxial Tension. Part 2. Testing by Biaxial Loading in the Plane of the Sheet

We analyze specific features of the design of equipment used for mechanical testing of sheet structural materials under the conditions of biaxial static, cyclic, or dynamic loading. We propose original solutions of the problems related to the fatigue testing of crosslike specimens performed without using complex hydraulic systems and their dynamic testing carried out by using very simple testing machines for uniaxial tension–compression.     

Analytical Calculation of Large-Scale Deflection of Pulse-Loaded Elliptic Plates

Large deflections of pulse-loaded elliptic and round plates made of hardenable elastoplastic materials are investigated analytically using an energy-based approach. Formulas that are convenient for engineering design have been derived.     

连续重整装置仿真系统的设计开发

为提高操作人员对连续重整装置开停工及事故处理的熟练程度，并对生产进行指导，采用半机理模型结合设计和现场数据介发的连续重整装置仿真系统已在现场成功投用。介绍了该仿真系统的软硬件结构、动态模型及仿真功能。     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。