喷射成形技术在钢铁材料中的应用

本文简要介绍了喷射成形技术的原理、特点及其在钢铁材料中的应用概况 ,综述了各种喷射成形钢铁材料的研究现状及其产品发展状况     

浅谈流化床干燥器布风板的设计

介绍流化床干燥器所用各种形式布风板的结构。并对其使用情况作了分析。特别对高温布风板的形式进行了探讨。     

Reply to the Comment by K. Jorgensen et al. to “Analysis of constant rate period of spray drying of slurry”

Previously developed model for spray drying of slurry droplets with high solid content (Liang, 2001) was revised to describe correctly a boundary condition on the outer surface of droplet on basis of the rate of liquid evaporation.     

Effects of Component Arrangement and Ambient and Drying Conditions on the Performance of Heat Pump Dryers

Performances of five heat pump dryer (HPD) configurations were studied by computer simulation. The component arrangement covers the fully open, the partially open, and the fully closed systems with external condenser or external cooler. The HPD performance was investigated for high and low drying rate and within the ambient temperature range of 20°C to 40°C. The best operating mode of the HPD depends on both drying rate and ambient condition. For the case of tropical climate and high drying rate, the partially open system is the optimum operating mode in general, except at some particular conditions where the fully open and fully closed systems are recommended. However, the operation for the low drying rate is more complicated, as the optimum configuration is sensitive to the change of ambient temperature.     

Spray drying conditions and encapsulating composition effects on formation and properties of sodium diclofenac microparticles

This paper reports the preparation and characterization of sustained release sodium diclofenac microparticles by spray drying. Aqueous dispersions of ethyl cellulose (Surelease®) and Eudragit RS 30 D® were evaluated as controlled release polymers. The product properties (product moisture, size distribution, particle morphology, flow properties, total drug load, in-vitro dissolution studies, and encapsulating efficiency) were determined as a function of inlet temperature of the spray drying, the feed flow rate and composition of the microencapsulating formulation. In general, lower values of the product moisture content were observed at higher drying temperatures. The spray-dried product was composed mainly by rounded-shape and multi-size particles. The mean particle diameters of the Eudragit based microparticles tended to be slight bigger than the Surelease based microparticles. The spray dried microparticles showed delayed drug dissolution rates, sustaining the drug release for several hours. These findings confirm the feasibility of the spray drying for preparation of microparticles with sustained release properties. The physical and chemical properties of the microparticles can be changed by varying the spray drying parameters as well as the microencapsulating formulation.     

盘式干燥机在高纯碳酸钡生产中的应用

对盘式干燥机的工作原理、结构特点进行了详细介绍，并将其它干燥设备和盘式干燥机作了对比，指出高纯碳酸钡行业采用盘式干燥机可以将生产成本降到最低限度，而产品质量可以得到很大提高。盘式干燥机也可用于高纯碳酸锶、硫酸钡等粘性物料的干燥，效果也非常理想，应用前景广阔。     

A MECHANISTICALLY BASED MATHEMATICAL MODEL OF SULFUR DIOXIDE ABSORPTION INTO A CALCIUM HYDROXIDE SLURRY IN A SPRAY DRYER

A mathematical model has been developed to predict So₂ absorption and removal during the constant rate drying period of a spray dryer. The model, based on film theory, treats the atomized slurry droplets as spheres containing discrete sorbent particles of slaked lime with the fluid uniformly distributed around the individual particles. The model includes gas and liquid phase mass transfer coefficients as well as resistance to Ca(OH)₂ dissolution. A sensitivity analysis has been conducted and a comparison was made between pilot-scale experimental data and model-predicted values of S0₂ removal efficiency.     

蒸汽管回转干燥机在硫精砂干燥中的应用

主要介绍蒸汽管回转干燥机的结构及 1 200 t/d 硫精砂干燥机的设计.与传统采用热风作为干燥介质的回转窑式干燥机相比,蒸汽管回转干燥机采用硫酸废热发电系统抽出的低压蒸汽作为干燥介质,热源稳定,节省用煤,并且不产生新的硫污染.试验表明,当物料ω(H2O)低于 15% 时,处理量和干燥强度基本在设计范围内,载气温度 110～123℃,相当安全.     

ALKYD PAINT WASTE CHARACTERIZATION AND DISTILLATION

In the present study the characterization and distillation of alkyd paint waste have been carried out in order to establish the technical viability of organic solvents recovery and to decide upon the best environmental management for the waste stream from a paint spray-booth application in an automotive component factory. The paint is a black primer based on an alkyd resin with toluene and xylene as solvents, black carbon as pigment, fillers, and other minor components.

The paint, paint wastes, and distillation wastes have been characterized by determination of the physicochemical properties of the solid (solvents content and flash point) and determination of ecotoxicity (EC₅₀), total organic carbon (TOC), and metals concentration of the leachates. The highly volatile matter (HVM) content, determined by the weight loss at 200°C, has been used as a parameter to relate with the hazardous wastes regulations based on the characterization parameters EC₅₀, TOC, and flash point.

Distillation experiments have been performed in a simple batch mode with mixtures of paint waste, water, and additives in order to obtain high efficiencies in the recovery of volatile organic compounds and to obtain a final solid with nonhazardous behavior and good manageability qualities. A fractional factorial design (2^3-1) of experiments was carried out in order to study the influence of the distillation variables: water/paint waste ratio (2/1-3/1 (g/g)), temperature (110°-145°C), alkaline additives (Na(OH),CaO, Ca(OH)₂), and amount of other additives (wt.% of bentonite, cement, and Ca(OH)₂) on the solvent recovery, [% VOCs]_Recovery, on the residual volatile organic compounds, [% VOCs]_{Distillation Waste}, and on the total organic content (TOC) of the waste leachates. The present work shows the quantitative results of the alkyd paint waste distillation process under optimum conditions.