喷射沉积柱状坯形状模型

通过坐标跟踪法建立了沉积坏形状预测模型。该模型不但考虑沉积坯任何表面点身自位置变化对沉积效果的影响，同时考虑了该点温度和其它表面点位置对该点沉积效果的影响，其计算过程严格按照喷射成形的实际过程执行，可实时计算并记录沉积坯的形貌，并验证了计算效果。本文模型可用于多种工艺下喷射沉积坯的形状预测。     

第三代伞状喷雾的分布特性及多片喷雾系统的应用研究

为解决前两代伞状喷雾在高背压下贯穿距不足的问题,借鉴碰撞喷雾方式,提出了第三代伞状喷雾概念。通过高速摄影对喷雾的分布特性进行了研究,结果表明:喷雾具有贯穿距可设定、扩散度高、空间分布均匀等特点。为避免碰撞后二次油束雾线相互干涉,又提出了一种多片喷雾概念,并在单缸四气门135柴油机上对多片喷雾燃烧系统进行了初步的性能试验,结果显示:系统能够有效地促进缸内均质混合气的形成;在供油提前角为19°CA时,全负荷范围内柴油机的油耗和碳烟排放均较低。     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Fabrication and characterization of Cu2ZnSnS4 thin films deposited by spray pyrolysis technique

We have investigated synthesis conditions and some properties of sprayed Cu₂ZnSnS₄ (CZTS) thin films in order to determine the best preparation conditions for the realization of CZTS based photovoltaic solar cells. The thin films are made by means of spraying of aqueous solutions containing copper chloride, zinc chloride, tin chloride and thiourea on heated glass substrates at various temperatures. In order to optimize the synthesis conditions of the CZTS films, two series of experiments are performed. In the first series the sprayed duration was fixed at 30 min and in the second it is fixed at 60 min. In each series, the substrate temperature was changed from 553°K to 633°K. The X-ray diffraction shows, on one hand, that the best crystallinity was obtained for 613°K as substrate temperature and 60 min as sprayed duration. On the other hand, these CZTS films exhibit the kesterite structure with preferential orientation along the [112] direction. Atomical Force Microscopy was used to determine the grain sizes and the roughness of these CZTS thin film. After the annealing treatment, we estimated the optical band-gap energy of the CZTS thin film exhibiting the best crystallinity as 1.5 eV which is quite close to the optimum value for a solar cell.     

Characterization of CuInS2 thin films for solar cells prepared by spray pyrolysis

We have made a study of the chemical composition, the electrical, the optical and the structural properties of polycrystalline CuInS₂ thin films prepared by spray pyrolysis to be used for thin film solar cells. These films were deposited starting from aqueous solutions with different chemical compositions ([Cu]/[In] and [S]/[Cu] ratios) and at different substrate temperatures. In all cases, the material is p-type with grains preferentially oriented in the (112) direction of the sphalerite structure. The electro-optical properties show a very strong dependence on the [Cu]/[In] ratio in the solution. Films with copper excess have smaller resistivity and better crystallinity than those which are stoichiometric or have indium excess. The results obtained in this work show the possibility of having CuInS₂ thin films with a wide range of resistivity, a fact that could be important for making solar cells based on this material.     

仪表空气干燥器控制系统的升级改进

利用工厂现有优势资源,自主对故障率逐步升高的仪表空气干燥器控制系统进行升级改进,从而提高重要单元设备运行的可靠性。     

喷射成形高温合金沉积态组织的形成与演变

对喷射成形高温合金的组织形成及其从雾化过程的树枝晶向等轴晶组织的演变过程进行了分析，结果表明，半液态层中发生的枝晶破碎，重熔所造成的核心增殖作用为等轴晶组织的形成提供了大量结晶核心，在此基础上枝晶臂的合并，粗化以及未严重固相枝晶的粗化和均匀化产生了喷射成形材料所持有的非枝非等轴晶组织。     

记第二届环太平洋先进材料及工艺国际会议

介绍第二届环太平洋先进材料及工艺国际会议情况，重点报导韩国钢铁工业、早期凝固过程研究、喷射成形、非晶合金、纳米材料和第三代单晶铸造高温合金等内容。     

常减压蒸馏装置高温部位的腐蚀与防护

阐述了常减压蒸馏装置高温部位的腐蚀机理，介绍了高温防腐蚀的三种方法：正确选材、高温缓蚀剂技术及喷涂渗铝技术，建议在类似的石化装置推广使用。     

高炉风口表面处理技术

介绍近代高炉风口采取等离子喷涂、各种金属渗镀和堆焊高温耐磨合金3种方法进行表面处理的情况。我国中小高炉多趋向发展多元金属渗镀,前苏联和日本风口经堆焊后抗磨性能有明显改善,采用上述3种处理后风口寿命均有数倍的提高。