Drying of Probiotics: Optimization of Formulation and Process to Enhance Storage Survival

This work describes how probiotic bacteria can be dried at low temperature in two steps, combining spray drying and vacuum drying, in order to enhance their survival during storage. A sufficient number of dried probiotics survived storage for more than 3 months at 30°C, if an appropriate combination of protein and carbohydrate was selected as carrier and storage conditions were maintained optimal. The use of soy protein and maltodextrin or skim milk and arabic gum resulted in the best survival rates of probiotics during storage. No evident difference was found between different spray dryer configurations, although a cocurrent flow was preferred.     

耐火纤维喷涂技术的优越性及应用

详细介绍了耐火纤维喷涂技术及施工等各方面的优越性。同时说明耐火纤维喷涂技术,在大庆石化公司炼油厂润滑油白土装置扩建改造中加热炉炉衬上的应用及取得的明显节能效果。     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Fabrication and characterization of Cu2ZnSnS4 thin films deposited by spray pyrolysis technique

We have investigated synthesis conditions and some properties of sprayed Cu₂ZnSnS₄ (CZTS) thin films in order to determine the best preparation conditions for the realization of CZTS based photovoltaic solar cells. The thin films are made by means of spraying of aqueous solutions containing copper chloride, zinc chloride, tin chloride and thiourea on heated glass substrates at various temperatures. In order to optimize the synthesis conditions of the CZTS films, two series of experiments are performed. In the first series the sprayed duration was fixed at 30 min and in the second it is fixed at 60 min. In each series, the substrate temperature was changed from 553°K to 633°K. The X-ray diffraction shows, on one hand, that the best crystallinity was obtained for 613°K as substrate temperature and 60 min as sprayed duration. On the other hand, these CZTS films exhibit the kesterite structure with preferential orientation along the [112] direction. Atomical Force Microscopy was used to determine the grain sizes and the roughness of these CZTS thin film. After the annealing treatment, we estimated the optical band-gap energy of the CZTS thin film exhibiting the best crystallinity as 1.5 eV which is quite close to the optimum value for a solar cell.     

Characterization of CuInS2 thin films for solar cells prepared by spray pyrolysis

We have made a study of the chemical composition, the electrical, the optical and the structural properties of polycrystalline CuInS₂ thin films prepared by spray pyrolysis to be used for thin film solar cells. These films were deposited starting from aqueous solutions with different chemical compositions ([Cu]/[In] and [S]/[Cu] ratios) and at different substrate temperatures. In all cases, the material is p-type with grains preferentially oriented in the (112) direction of the sphalerite structure. The electro-optical properties show a very strong dependence on the [Cu]/[In] ratio in the solution. Films with copper excess have smaller resistivity and better crystallinity than those which are stoichiometric or have indium excess. The results obtained in this work show the possibility of having CuInS₂ thin films with a wide range of resistivity, a fact that could be important for making solar cells based on this material.     

仪表空气干燥器控制系统的升级改进

利用工厂现有优势资源,自主对故障率逐步升高的仪表空气干燥器控制系统进行升级改进,从而提高重要单元设备运行的可靠性。     

喷射成形高温合金沉积态组织的形成与演变

对喷射成形高温合金的组织形成及其从雾化过程的树枝晶向等轴晶组织的演变过程进行了分析，结果表明，半液态层中发生的枝晶破碎，重熔所造成的核心增殖作用为等轴晶组织的形成提供了大量结晶核心，在此基础上枝晶臂的合并，粗化以及未严重固相枝晶的粗化和均匀化产生了喷射成形材料所持有的非枝非等轴晶组织。     

记第二届环太平洋先进材料及工艺国际会议

介绍第二届环太平洋先进材料及工艺国际会议情况，重点报导韩国钢铁工业、早期凝固过程研究、喷射成形、非晶合金、纳米材料和第三代单晶铸造高温合金等内容。     

常减压蒸馏装置高温部位的腐蚀与防护

阐述了常减压蒸馏装置高温部位的腐蚀机理，介绍了高温防腐蚀的三种方法：正确选材、高温缓蚀剂技术及喷涂渗铝技术，建议在类似的石化装置推广使用。     

喷射成形技术在钢铁材料中的应用

本文简要介绍了喷射成形技术的原理、特点及其在钢铁材料中的应用概况 ,综述了各种喷射成形钢铁材料的研究现状及其产品发展状况