改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

影响混凝土强度的因素及控制措施

分析了水泥强度等级、水灰比和骨料质量等内因,及施工条件、养护温度、湿度、龄期等外因对混凝土强度的影响,并提出了控制混凝土强度的相应措施,以确保混凝土强度符合设计及施工要求,从而保证建筑物结构安全。     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Characterization of strength properties of thin polycrystalline silicon films for MEMS applications

The aim of this work is to characterize the strength properties of polycrystalline silicon (polysilicon) with the use of tensile and bending test specimens. The strength of thin polysilicon films with different geometry, size and stress concentrations has been measured and correlated with the effective size of the specimen and its stress distribution. The test results are evaluated using a probabilistic strength approach based on the weakest link theory with the use of STAU software. The use of statistic methods of strength prediction of polysilicon test structures with a complex geometry and loading based on test values for standard material tests specimen has been evaluated.     

Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.     

Express Method for Estimation of Tensile Strength and Crack Resistance of Brittle Media

The procedure is proposed for estimating the crack resistance and tensile strength of rocks by the results of experiments on disk samples with holes. The gradient approach to the strength problem is employed in processing the experimental data.     

Determination of shear strength values according to EN 408

This paper presents the results of 382 shear tests carried out according to EN 408. The test pieces consisted of spruce (Picea abies) and varied in density and ring width orientation (radial, tangential and at an angle of 45° to the steel plates). In addition pieces containing pith and knots were tested. The paper discusses problems observed when using this test configuration and shows that the test results do not support the characteristic shear strength values as given in EN 338. Moreover, the test results do not support the relationship between characteristic shear strength and characteristic bending strength as given in EN 384.

---

Résumé Cet article présente les résultats de 382 essais de cisaillement menés conformément à EN 408. Les éprouvettes d’essai sont en épicéa (Picea abies) et présentent une variabilité en termes de masse volumique et d’orientation des cernes d’accroissement (radiale, tangentielle, à un angle de 45° par rapport aux plaques métalliques). Des éprouvettes supplémentaires contenant du cœur et des nœuds ont également été testées. L’article évoque les problèmes qui ont été mis en évidence lors de l’utilisation de ce dispositif expérimental et montre que les résultats expérimentaux ne sont pas en accord avec les valeurs caractéristiques de résistance au cisaillement données dans EN 338. De plus, ces résultats ne confirment pas la relation entre résistance caractéristique au cisaillement et résistance caractéristique à la flexion telle que stipulée dans EN 384.

     

电接点压力表补水泵定压系统的应用

阐述了电接点压力表补水泵定压系统的一些应用问题 ,给出了电接点压力表定压点的上、下限计算公式 ,并提出了该系统补给水泵、补给水箱及安全阀的设计选型方法