离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

Ф16mm、Ф18mm钼棒的研制

采用等静压制法，压制钼圆棒坯，经中频高温烧结，制得尺寸适合、用户满意的钼电极棒。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

应用均匀设计法研究安息香缩合工艺

利用均匀设计法通过SPSS10.0计算机软件研究了反应条件对安息香缩合的影响。从而获得优化的工艺条件，与正交试验相比，该法试验次数少。工作效率高，并且便于分析各种因素的影响。     

深亚微米集成电路的快速时域仿真技术

随着深亚微米集成电路技术的发展，集成电路的规模越来越大，工作频率越来越高，并正朝着系统集成的方向发展，因而在模拟速度，模拟精度和可模拟的电路规模等各个方面对电路仿真技术提出了新的要求。近年来，各种新的电路仿真方法和仿真系统用相继脱颖百出，并将取代那些传统的，已经无法适应深亚微米技术发展的电路仿真器。     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

Minimal communication cost software construction in the Internet environment

This paper investigates the issue of building software in the Internet environment, where local area network (LAN) based systems are interconnected by links with different bandwidth and do not share file systems. The software is modeled as a directed acyclic graph. Each node in the graph represents a logical step in processing the software while the edges describe the order of execution. The problem is to construct the software at a particular LAN with minimum Internet communication cost. An optimal polynomial algorithm, SOFTCON, with time complexity is presented, where and are the number of nodes and edges in the graph describing the software respectively, is the number of LANs in the Internet environment, and is the time complexity of the network flow algorithm on the flow network with nodes and edges transformed from the directed acyclic graph of the software. Received: 6 December 1995 / 1 May 1996     

一个表示和运用非功能性需求的框架

本文分析了一个软件开发进程中表示和运用非功能性需求的综合框架，该框架的目的是开发一套技术以调整软件开发进程中的设计决策，从而强调了依据非功能需求，探索合理化的软件开发进程。     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

On solving constrained optimization problems with neural networks:a penalty method approach

Deals with the use of neural networks to solve linear and nonlinear programming problems. The dynamics of these networks are analyzed. In particular, the dynamics of the canonical nonlinear programming circuit are analyzed. The circuit is shown to be a gradient system that seeks to minimize an unconstrained energy function that can be viewed as a penalty method approximation of the original problem. Next, the implementations that correspond to the dynamical canonical nonlinear programming circuit are examined. It is shown that the energy function that the system seeks to minimize is different than that of the canonical circuit, due to the saturation limits of op-amps in the circuit. It is also noted that this difference can cause the circuit to converge to a different state than the dynamical canonical circuit. To remedy this problem, a new circuit implementation is proposed.