Identification of cysteine pairs within the amino-terminal 5% of apolipoprotein B essential for hepatic lipoprotein assembly and secretion

There is growing evidence that the amino-terminal globular domain of apolipoprotein B (apoB) is essential for lipoprotein particle formation in the hepatic endoplasmic reticulum. To identify the structural requirements for its function in lipoprotein assembly, cysteine (Cys) pairs required to form the seven disulfide bonds within the amino-terminal 21% of apoB were replaced in groups or individually by serine. Substitution of Cys pairs required for formation of disulfide bonds 1-3 or 4-7 (numbered from amino to carboxyl terminus) completely blocked the secretion of apoB28 in transfected HepG2 cells. To identify the specific disulfide bonds required for secretion, Cys pairs were mutated individually. Substitution of Cys pairs required for disulfide bonds 1, 3, 5, 6, or 7 had little or no impact on apoB28 secretion or buoyant density. In contrast, individual substitution of Cys pair 2 (amino acid residues 51 and 70) or 4 (218 and 234) severely inhibited apoB28 secretion and its capacity to undergo intracellular assembly with lipid. The same assembly and secretion defects were observed when these mutations were expressed as part of apoB50. These studies provide direct evidence that the ability of the internal lipophilic regions of apoB to engage in the recruitment and sequestration of lipid during translation is critically dependent upon a structural configuration contained within or affected by the amino-terminal 5% of the protein.     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

大系统分散鲁棒容错控制的进展及主要成果

综述了近２０年来关联大系统分散鲁棒容错控制的研究动态及取得的主要成果。说明了统一地研究分散鲁棒容错控制的必要性。在分散控制、鲁棒控制和容错控制研究领域内，分析了各种设计方法的主导思想及实质；指出了这些研究成果的意义与存在的问题。文中着重论述了分散、鲁棒、容错控制研究方法的发展途径。     

Magnetization and rotation of MTG HTSC ring in magnetic field

The magnetization of a melt-texture growth (MTG) HTSC ring has been studied. It is shown that the magnetic field inside the ring is larger than the external field under a certain range of external magnetic fields. We have also investigated the magnetic field dependence of the response of a detective coil near a rotating superconducting ring. The responses of the MTG sample are different for different cooling methods.     

Modeling and CW operation of a quasi-three-level 946 nm Nd: YAG laser

A model is developed for an end-pumped quasi-three-level laser with population in the lower laser level at equilibrium such as for transitions to the manifolds⁴I9/2in Nd³⁺,⁴I15/2in Er³⁺,⁵I8in Ho³⁺and³H6in Tm³⁺. It is shown that the effect of residual lower laser level population on laser operation can be treated as a saturable loss. Room temperature operation on the⁴F3/2-⁴I9/2transition in Nd:YAG under CW dye laser pumping has been demonstrated with a threshold as low as 11.5 mW incident power and a slope efficiency of 7 percent with 0.3 percent output coupling. Performance is limited by the low output coupling and diffraction loss.     

An experience of tunnelling in mudstone area in southwestern Taiwan

Many tunnels will be constructed in southwestern Taiwan in the upcoming decade to meet the huge demands of transportation, energy and water infrastructure projects. Mudstone strata cover more than a 1000 km² area, consisting mainly of massive mudstone or alternation of mudstone and sandy layer, exhibiting unfavorable geological and hydrological characteristics, making it extremely difficult for tunnelling. This paper presents the lessons learned from three tunnelling projects in the 1990s in a mudstone area. In addition to discussing the rock behavior in the vicinity of tunnel and its failure patterns, the monitoring data during tunnelling are presented as well. Finally, the effective method of design and construction are recommended for tunnelling in mudstone area.     

展成式精密电火花加工机床

研制了一种展成式精密电火花加工机床，它含有3个回转机构和4个直线移动机构，工件苡轴，工具电极苡轴和转台均可按需要回转，坐标工作台可作纵向和横向移动，工件头架可作轴向和竖向移动。可设置成多种复合运动方式和相应的结构布局，具有很丰富的加工功能，加工精度能达到微米级并实现电火花镜面加工。     

D36580/97t锥顶储罐罐顶桁架的整体吊装和旋转就位

本文针对大型储罐罐顶整体桁架结构尺寸大、质量大、易变形的特点,详细介绍了一种切实可行的整体吊装及旋转就位方法。从选定吊装方案入手,阐叙了实现本方法的思路和技术细节,提出了实施过程中的注意事项。实践证明,该方法能保证安装质量,安全、可靠、可行。     

大坝安全监控专家系统中的知识处理

在介绍产生式规则及其数学模型的基础上，论述了用成熟的关系数据库 技术来表示和存储产生式规则表示的专家知识的方法，较好地解决了知识的存储和管理问题 。同时，利用关系数据库中实体间的关系，很容易将分散存储的规则元素组合成规则供推理 时使用。在分析了大坝安全监控专家系统知识特点的基础上举例说明了用关系数据库表 示产生式规则的具体方法。     

局部设有钢筋砼电梯井墙的设计探讨

本文就局部设有钢筋砼电梯井的工程计算及理论分析，阐明分析了少墙的框剪结构的设计及注意问题。