Heat transfer to laminar flow with temperature — dependent heat generation

Two problems were solved theoretically on the heat transfer to circular tube flow with internal heat source. The one problem is to maintain the mixed-mean temperature of fluid at the inlet temperature. The other is a conjugated problem with a uniformly specified temperature at the outside surface of the wall, accounting for the wall conduction. From the numerical example for the former, it is shown that the mixed-mean temperature can be controlled within 15% error under the estimated condition. From the numerical results for the latter, it is concluded that the influence of wall conduction is more serious than the case without heat generation.     

Effect of platelet-activating factor on lipoprotein lipase and blood lipids

We investigated the effect of platelet-activating factor (PAF) and of the PAF specific antagonist CV-6209 on plasma lipid metabolism, and particularly on post-heparin plasma lipolytic activity in male Wistar rats. Lipoprotein lipase (LPL) activity was enhanced by intravenous injection of PAF before intravenous injection of heparin when the PAF dose was low (0.2 μg/kg). PAF activated hepatic triacylglycerol lipase (HTGL) activity dose-dependently. Plasma triacylglycerols (TG) significantly decreased with the activation of LPL and/or HTGL. Plasma total cholesterol (TC) and phospholipid (PL) levels decreased at a low dose of PAF (0.2 μg/kg), but increased when higher doses were used. The PAF antagonist CV-6209 partially reversed the PAF induced effects on HTGL, TC and PL. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, Tokyo, Japan, May 1989.     

Continuous-velocity lattice gas cellular automata for miscible binary fluid and its application to simulation of interface instability

Continuous-velocity lattice gas cellular automata (CVLGA) is extended to miscible binary fluid systems. A new parameter is introduced in order to control the diffusivity of the fluids. The correlation between the diffusivity and the new parameter proves that there exists the maximum value of the diffusivity. Quantitative verifications of the model are carried out with numerical simulations of the diffusion phenomena across a falling fluid film. The model is then applied to the simulations of Rayleigh-Taylor instability during the gravitational mixing phenomena. The qualitative tendency of the growth of the interface instability is the same as that obtained in conventional numerical methods.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

Decomposition of Carbon Dioxide to Carbon with Active Wustite at 300°C

Active wustite (FeδO, with a δ value of 0.98) was prepared by keeping normal wustite (δ value of 0.94) in a N₂ atmosphere at 300°C for 10 min. This reaction is given by (4δ₂–3)Fe_δ1O→(4δ₁–3)Fe_δ2O + (δ₂–δ₁)Fe₃O₄ where δ₁= 0.94 and δ₂= 0.98. The equation indicates that the normal wustite undergoes eutectoid decomposition into active wustite and stoichiometric magnetite (Fe₃O₄). Carbon dioxide (1.013 × 10⁵ Pa) was almost completely (100%) decomposed into carbon (zero valence) by the active wustite at the low temperature of 300°C, which was associated with the transformation of the active wustite into the stoichiometric magnetite. The internal pressure of the reaction cell eventually became a vacuum.     

Electron-beam irradiation-induced grafting of acrylonitrile onto polyethylene

Low- and high-density polyethylene (PE) films were grafted with acrylonitrile (AN) by electron beam prior to irradiation. The distribution of graft chains over the cross section of the sample film was analyzed in terms of the distribution of nitrogen atoms contained in the AN by means of an electron probe microanalyzer (EPMA), and graft sites were studied in relation to the effect of grafting temperature on the percent graft and the oxygen permeability of the sample films. It was found that diffusion of AN into the film was the rate-limiting step in the grafting process, thus restricting the grafting to the surface of the film in the initial grafting stages. However, the grafting shifted to the center of film as the graft process proceeded, until a uniform distribution of graft chains was observed across the entire film thickness. High-density polyethylene (HDPE) was found to display a higher percent graft than did low-density polyethylene (LDPE), and percent graft tended to increase with increasing grafting temperature. On the other hand, film oxygen permeability decreased with increasing percent graft, but this decreasing trend decreased with increasing percent graft. These findings suggest that the grafting is initiated by radicals trapped in the amorphous phase near the crystalline regions and at the surface of crystallites and that graft chains grow toward the amorphous regions. As for the radicals contributing to graft polymerization, it appears that AN permeates deeper near the crystalline surface and that graft chains grow from these sites.     

Experimental analyses for electronic structure of barium zirconate-strontium zirconate proton-conducting solid solution

In proton-conducting oxides, analyses for their electronic structure contribute to the understanding of interactions between defects in them. In this study, electronic band alignment of (1−x)BaZr_0.8Y_0.2O_3−δ(BZY)–xSrZr_0.95Y_0.05O_3−δ(SZY) proton-conducting solid-solution system (BSZY) which has high defect concentration and the deep valence band is experimentally investigated. By using thin-film specimens for optical absorption measurements, absorption edges derived from electron transition from the valence band to the conduction band which was insensitive to the proton incorporation were clearly observed in spite of the high defect concentration. The obtained optical band gap energy increased from 5.61 to 5.89 eV with increasing x, which was consistent with a composition dependence of Zr(Y)O₆ octahedral tilting. Ultraviolet photon-yield spectroscopy (UV-PYS) measurements under vacuum condition revealed that BZY and SZY had ionization energy of 6.98 and 7.31 eV, respectively, and thus the absolute energy levels of the valence band maximum and the conduction band minimum of BSZY were experimentally clarified. We propose that the combination of the optical absorption measurements using thin-film specimens and the UV-PYS measurements under vacuum condition is effective in evaluating fundamental electronic structures of proton-conducting oxides.     

Adaptive interpolation scheme for NURBS curves with the integration of machining dynamics

This paper develops a comprehensive interpolation scheme for non-uniform rational B-spline (NURBS) curves, which does not only simultaneously meet the requirements of both constant feedrate and chord accuracy, but also real-time integrates machining dynamics in the interpolation stage. Although the existing work in this regard has realized the importance to simultaneously consider chord error and machining dynamics, none has really incorporated these in one complete interpolation scheme. In this paper, machining dynamics is considered for three aspects: sharp corners or feedrate sensitive corners on the curves, components with high frequencies or frequencies matching machine natural ones and high jerks. A look-ahead module was developed for detecting and adaptively adjusting the feedrate at the sharp corners. By Fast Fourier Transform (FFT) analysis with a moving window in the interpolation stage identified were some special frequency components such as those containing high frequencies or with frequencies matching machine natural ones. Then, the notch filtering or time spacing method was used to eliminate these components. To more completely reduce feedrate and acceleration fluctuations, the jerk-limited algorithm was also developed. Finally, the interpolated feedrate was further smoothened with B-spline fitting method and the NURBS curves were re-interpolated with the smoothened feedrate. During the interpolation, the chord error was repeatedly checked and confined in the prescribed tolerance. Two NURBS curves were used as examples to test the feasibility of the developed interpolation scheme.     

Improvement of Formability by Oscillation of Internal Pressure in Pulsating Hydroforming of Tube

A new history of internal pressure in the hydroforming processes of tubes is developed to attain high formability. The effect of improvement of formability by the oscillation of internal pressure in a pulsating hydroforming process of tubes is examined using both finite element simulation and experiment. The deformation behaviour during the hydroforming is greatly affected by the oscillation of internal pressure. For a monotonic history of small internal pressure, the wrinkling was caused by insufficient bulging, whereas the necking and bursting occurred for a monotonic history of large internal pressure. The occurrence of these defects can be avoided by oscillating the internal pressure in the pulsating hydroforming. The improvement of formability in the pulsating hydroforming is due to both low pressure and oscillation of pressure. The effects of the amplitude and cycle number of pressure in the pulsating hydroforming on the deformation behaviour are investigated. It is found the oscillation of internal pressure is effective in preventing the occurrence of defects.     

Fault tolerant approach for biosignal-based robot control

This paper proposes a fault tolerant framework for biosignal-based robot control with multiple sensor electrodes. In this approach, to cope with sensor faults, a reliable joint torque estimation model is selected from a group of estimation models based on sensor failure classifiers. The correlation among the electromyography (EMG) signal streams is used as input feature vectors for fault detection. To validate our proposed method, we artificially disconnect an EMG electrode or detach one side of an EMG probe from the skin surface during elbow-joint torque estimation experiments with five participants. When one EMG sensor electrode experiences one of the problems, the experimental results show that the joint torque can be estimated with significantly fewer errors using our proposed approach than a joint torque estimation method without sensor fault detection or than a method with a conventional sensor fault detection algorithm. Furthermore, we controlled a mannequin-arm-attached one-DOF exoskeleton based on the estimated torque profiles by generating movements with the estimated torque derived from the selected model.