Irradiation of large area Mylar membrane and characterization of nuclear track filter

Ion irradiation of Si⁸⁺ ion beam of 100 MeV was scattered by a gold foil on a Mylar membrane of 25 Μm thickness in the form of film roll (width, 12.5 cm and length, 400 cm) at the Nuclear Science Centre, New Delhi. The characterization of etched nuclear tracks was carried out by gas permeation measurements. The samples cut from the film roll of required size for permeability measurements were etched in a controlled manner in a constant temperature bath of 6N NaOH solution. The opening of the conical etched tracks was characterized by hydrogen gas permeation.     

Effect of iron content on permeability and power loss characteristics of Li0.35Cd0.3Fe2.35O4 and Li0.35Zn0.3Fe2.35O4

Substituted lithium ferrites having the chemical formula, Li_0.35Cd_0.3Fe_2.35O₄ and Li_0.35Zn_0.3Fe_2.35O₄, with different iron (metal) contents (2, 4, 6, 8 and 10) in wt% have been prepared by solid-state technique. Complex permeability and power loss of all samples have been measured by network analyser in the frequency range of 50–5000 kHz. Magnetic properties like saturation magnetization, coercivity, retentivity have been measured by vibrating sample magnetometer (VSM). The permeability of cadmium doped lithium ferrites exhibited higher values than zinc doped lithium ferrites. The power loss of cadmium doped lithium ferrites is lesser as compared to zinc doped lithium ferrites in the frequency range of 50–5000 kHz and at flux density of 10 mT. The behaviour of power loss with flux density has been found near about same for both series. Magnetic and power loss behaviour of the samples suggest that a small amount of Fe content can improve the properties of ferrite samples for microwave devices.     

Approximation of Well Function and Identification of Leaky Aquifer Parameters

The existing equation for leaky aquifers is transformed into a nondimensional form using new parameters and a scaled well function for leaky aquifers is proposed. A computationally simple function is developed for accurately approximating the scaled well function for the practical range of the parameters. Utilizing this function (approximation), an optimization method is proposed for identifying the leaky-aquifer parameters from observed drawdowns. The new function has an enhanced utility when a repetitive numerical evaluation of the well function for leaky aquifers is needed, e.g., while estimating the aquifer parameters using optimization or Kalman filter or artificial neural network methods. The application of the proposed method is illustrated using a few sets of published data. The proposed method outperforms the extended Kalman filter method, based on the reported results in the literature.     

Perpetual effect of laser surface texturing on tribological properties of Ti3SiC2/GNP composite—A fretting wear study

Tribological properties of Ti₃SiC₂ ceramic and Ti₃SiC₂/GNP composite were investigated using fretting sliding against Si₃N₄ ball counter body at a load of 50 N for a sliding distance of 900 m, under non-textured lubricated (NTL), textured lubricated (TL) condition, and textured lubricated high temperature (TLHT). This paper presents the influence of laser surface texturing (LST) on Ti₃SiC₂ and its graphene nanoplatelets (GNP) reinforced composite established through spark plasma sintering (SPS), tested under fretting wear conditions. The coefficient of friction and wear rate of Ti₃SiC₂ and its graphene nanoplatelets reinforced composites were incontrovertibly enhanced with laser surface texturing as compared to non-textured Ti₃SiC₂ and its GNP composite. The TL surface of Ti₃SiC₂ composite reinforced with 15% GNP showed the lowest COF and wear rate. Almost negligible changes were observed for TLHT tests. The LST proved to an efficient technique for enhancing the friction and wear properties of Ti₃SiC₂ and Ti₃SiC₂/GNP composite.     

Matheuristic approaches for Q-coverage problem versions in wireless sensor networks

This article deals with sensor coverage scheduling in wireless sensor networks subject to Q-coverage constraints. The main concern is to maximize the network lifetime, while ensuring that each target is covered by a given number of sensors. Three different variations of this problem are considered. Column generation based exact approaches are developed for those problems where the auxiliary problem is solved by a two-level approach comprising a genetic algorithm and an integer linear programming formulation. The genetic algorithm takes advantage of the auxiliary problem structure and appears to be very efficient at providing the master problem with attractive columns. The auxiliary problem integer linear programming (ILP) formulation is then mostly used for proving the optimality status of the current master problem solution. The proposed approaches are shown to be significantly faster than column generation approaches relying only on the auxiliary problem ILP formulation.     

Pressure-Dependent Behavior of Defect-Modulated Band Structure in Boron Arsenide

The recent observation of unusually high thermal conductivity exceeding 1000 W m⁻¹ K⁻¹ in single-crystal boron arsenide (BAs) has led to interest in the potential application of this semiconductor for thermal management. Although both the electron/hole high mobilities have been calculated for BAs, there is a lack of experimental investigation of its electronic properties. Here, a photoluminescence (PL) measurement of single-crystal BAs at different temperatures and pressures is reported. The measurements reveal an indirect bandgap and two donor–acceptor pair (DAP) recombination transitions. Based on first-principles calculations and time-of-flight secondary-ion mass spectrometry results, the two DAP transitions are confirmed to originate from Si and C impurities occupying shallow energy levels in the bandgap. High-pressure PL spectra show that the donor level with respect to the conduction band minimum shrinks with increasing pressure, which affects the release of free carriers from defect states. These findings suggest the possibility of strain engineering of the transport properties of BAs for application in electronic devices.     

Flaxseed: a potential source of food, feed and fiber

Flaxseed is one of the most important oilseed crops for industrial as well as food, feed, and fiber purposes. Almost every part of the flaxseed plant is utilized commercially, either directly or after processing. The stem yields good quality fiber having high strength and durability. The seed provides oil rich in omega-3, digestible proteins, and lignans. In addition to being one of the richest sources of α-linolenic acid oil and lignans, flaxseed is an essential source of high quality protein and soluble fiber and has considerable potential as a source of phenolic compounds. Flaxseed is emerging as an important functional food ingredient because of its rich contents of α-linolenic acid (ALA), lignans, and fiber. Lignans appear to be anti-carcinogenic compounds. The omega-3s and lignan phytoestrogens of flaxseed are in focus for their benefits for a wide range of health conditions and may possess chemo-protective properties in animals and humans. This paper presents a review of literature on the nutritional composition of flaxseed, its health benefits, and disease-prevention qualities, utilization of flaxseed for food, feed, and fiber, and processing of flaxseed.     

Optical and magnetic properties of Fe-doped CdS dilute magnetic semiconducting nanorods

Solvothermal technique has been used for the synthesis of Fe-doped CdS nanorods (Cd_1?xFe_xS) with (x = 0.0, 0.3, 0.5, 1.0, 1.5). Structural analysis carried out using X-ray diffraction reveals the formation of defect-free hexagonal phase of the CdS nanorods. Energy dispersive X-ray analysis confirms the presence of elements Cd, Fe and S in their stoichiometric ratio. Blue shift in the band gap, as compared to the bulk CdS, has been observed in UV–visible spectra. The decrease in the intensity of the photoluminescence peaks confirms the quenching of spectra upon Fe doping. Transmission electron microscopy, high-resolution transmission electron microscopy and selected area diffraction studies confirm the polycrystalline nature as well as growth of CdS nanorods along (112) plane. Magnetic study confirms the ferromagnetic nature of the synthesized nanorods. Magnetic saturation has been found to be 0.187, 0.300, 0.450, 0.675, 0.600 emu g^?1, respectively, for undoped, 3, 5, 10, and 15 % Fe-doped CdS.     

Recent Developments in Integrated Solar Combined Cycle Power Plants

Global concern for depleting fossil fuel reserves have been compelling for evolving power generation options using renewable energy sources. The solar energy happens to be a potential source for running the power plants among renewable energy sources. Integrated Solar Combined Cycle(ISCC) power plants have gained popularity among the thermal power plants. Traditional ISCC power plants use Direct Steam Generation(DSG) approach. However, with the DSG method, the ISCC plant’s overall thermal effici...     

Production and structural characterisation of dextran from an indigenous strain of Leuconostoc mesenteroides BA08 in Whey

In this work, the production of dextran was carried out in whey‐supplemented media using Leuconostoc mesenteroides BA08. Different growth and nutritional parameters were optimised to maximise the dextran production. Batch production in whey‐based media under optimised nutritional and growth conditions yielded a dextran concentration of 17.25 g/L. Structural analysis of the purified polymer by FT‐IR, 1D ¹H and ¹³C nuclear magnetic resonance methodology revealed that polymer was a linear dextran having 93% α‐(1→6) linkage in the main chain. The morphology of the dried dextran and dextran‐producing cells was also studied by scanning electron microscope which showed a granular and porous or weblike structure, respectively. The results obtained showed that the industrial whey supplemented with nutrients such as sucrose, yeast extract and K₂HPO₄ can serve as an ideal growth medium for dextran production. The optimised fermentation and nutritional parameters can be further scaled up to establish the potential for the commercial production of food‐grade dextran from whey as part of a novel cost‐effective and environment‐friendly approach.