Bandwidth allocation algorithms for weighted maximum rate constrained link sharing policy

This paper addresses the problem of bandwidth allocation under the weighted maximum rate constrained link sharing policy and proves a key theory in the condition of allocation termination. We propose several algorithms with various worst-case and average-case time complexities, and evaluate their computation elapse times.     

Characterizing the deformation behavior of Tertiary sandstones

Tertiary sandstones possess deformational behavior different from hard rocks, especially the relatively larger amount of volumetric dilation during shearing. Such excess dilation contributes to the increase of crown settlement during tunnel excavation and accounts for several cases of tunnel squeezing within Tertiary sandstones. Therefore, the deformation behavior of Tertiary sandstones sampled from more than 13 formations was studied. To distinguish the volumetric deformation induced by hydrostatic stress or by shear stress as well as to decompose the elastic and the plastic components of strains, special experimental techniques, including pure shear tests and cycles of loading–unloading were applied.The experimental results reveal that the deformation of Tertiary sandstone exhibits the following characteristics: (1) significant amount of shear dilation, especially elastic shear dilation; (2) non-linear elastic and plastic deformation; (3) plastic deformation occurs prior to the failure state. Furthermore, features of plastic deformation were inferred from experimental results and, as a result, the geometry of plastic potential surface and the hardening rule were accordingly determined. A constitutive model, involving nonlinear elastic/plastic deformation and volumetric deformation induced by shear stress, is proposed. This proposed model simulates the deformational behavior for the shear-dilation-typed rocks reasonably well. Furthermore, tests on the versatility of the proposed model, including varying hydrostatic stress and stress paths, indicate that the proposed model is capable of predicting deformational behavior for various conditions.     

Intelligent control of doubly‐fed induction generator systems using PIDNNs

An intelligent control for a stand‐alone doubly‐fed induction generator (DFIG) system using a proportional‐integral‐derivative neural network (PIDNN) is proposed in this study. This system can be applied as a stand‐alone power supply system or as the emergency power system when the electricity grid fails for all sub‐synchronous, synchronous, and super‐synchronous conditions. The rotor side converter is controlled using field‐oriented control to produce 3‐phase stator voltages with constant magnitude and frequency at different rotor speeds. Moreover, the grid side converter, which is also controlled using field‐oriented control, is primarily implemented to maintain the magnitude of the DC‐link voltage. Furthermore, the intelligent PIDNN controller is proposed for both the rotor and grid side converters to improve the transient and steady‐state responses of the DFIG system for different operating conditions. Both the network structure and online learning algorithm are introduced in detail. Finally, the feasibility of the proposed control scheme is verified through experimentation. Copyright © 2011 John Wiley and Sons Asia Pte Ltd and Chinese Automatic Control Society     

Synthesis and characterization of novel polyesterimides

A series of soluble novel polyesterimides was synthesized from diamines [a mixture of 2,2‐bis(4‐(4‐aminophenoxy)phenyl)propane (BAPP) with amine‐terminated polysiloxane (ATPS) in various mole ratios] and the ester‐group‐containing dianhydrides. The ester group containing dianhydrides in turn was synthesized by the transesterification reaction of trimellitic anhydride (TMA) with diacetate ester of hydroquinone (HQ), 4,4′‐dihydrophenyl (BP), 1,6‐hexanediol, or ethylene glycol. The resulted polyesterimides were characterized by using Fourier‐transform infrared spectroscopy, inherent viscosity, solubility, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The polyesterimides of BP and HQ had relatively high glass transition temperatures in the range of 214.7–227.2 and 195.7–210.5°C, respectively. The glass transitions decreased rather slowly with the increase in polysiloxane content. Thermal stability and the weight‐loss behavior of polyesterimides were studied by TGA. All polyesterimides of BP and HQ (BPI and HQI) showed no significant weight loss below 500°C in a N₂ environment, and the decomposition temperatures (T_d5%) of BPI and HQI were >520°C. Most polyesterimides were soluble in polar aprotic solvents and m‐cresol. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 730–738, 2004     

Novel positive‐working aqueous‐base developable photosensitive polyimide precursors based on diazonaphthoquinone‐capped polyamic esters

Novel positive‐working aqueous‐base developable photosensitive polyimide (PSPI) precursors based on partially diazonaphthoquinone (DNQ)‐capped polyamic esters bearing phenolic hydroxyl groups and a DNQ photosensitive compound (PIC‐3) were developed. The partially DNQ capped polyamic esters were prepared from an esterification reaction of 1,2‐naphthoquinone diazide‐5‐sulfonyl chloride with the polyamic esters. The partially DNQ capped polyamic esters decreased the dark film loss effectively in the aqueous‐base developer and were able to make thicker film resists compared to the uncapped polyamic esters. The 25 mol % DNQ‐capped BisAPAF–PMDA polyamic ester and BisAPAF–ODPA polyamic ester containing 25 wt % PIC‐3 photosensitive compound showed a sensitivity of 176 and 185 mJ/cm², and a contrast of 1.68 and 1.02, respectively, in a 3‐μm film with 1.25 wt % tetramethylammonium hydroxide developer. A pattern with a resolution of 5 μm was obtained from both PSPI precursor compositions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2293–2300, 2003     

Fischer–Tropsch synthesis. Compositional changes in an iron catalyst during activation and use

The equilibrium phase compositions of iron have been calculated for gas compositions that could be encountered during the Fischer–Tropsch synthesis. The gas compositions measured experimentally for CO conversion levels in the 30–90% range show that iron should be present as the carbide phase. However, experimental characterization of iron catalysts show that a significant fraction of the iron is present as Fe₃O₄ following synthesis for several days. A model that can account for the experimental catalyst phase composition and the gases present in the reactor would have a core of Fe₃O₄ and an outer layer of iron carbides.     

Synthesis and characterization of a positive‐working,aqueous‐base‐developable photosensitive polyimide precursor

A positive‐working, aqueous‐base‐developable photosensitive polyimide precursor based on poly(amic ester)‐bearing phenolic hydroxyl groups and a diazonaphthoquinone photosensitive compound was developed. The poly(amic ester) was prepared from a direct polymerization of 2,2′‐bis‐(3‐amino‐4‐hydroxyphenyl)hexafluoropropane and bis(n‐butyl)ester of pyromellitic acid in the presence of phenylphosphonic dichloride as an activator. Subsequently, the thermal imidization of the poly(amic ester) precursor at 300°C produced the corresponding polyimide. The inherent viscosity of the precursor polymer was 0.23 dL/g. The cyclized polyimide showed a glass‐transition temperature at 356°C and a 5% weight loss at 474°C in nitrogen. The structures of the precursor polymer and the fully cyclized polymer were characterized by Fourier transform infrared spectroscopy and ¹H‐NMR. The photosensitive polyimide precursor containing 25 wt % diazonaphthoquinone photoactive compound showed a sensitivity of 150 mJ/cm² and a contrast of 1.65 in a 3 μm film with 1.25 wt % tetramethylammonium hydroxide developer. A pattern with a resolution of 10 μm was obtained from this composition. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 352–358, 2002     

The solidification characteristics of 6061 and A356 aluminum alloys and their ceramic particle-reinforced composites

The solidification curve and viscosity are the two most important solidification characteristics. The solidification curves of the 6061 and A356 alloys and their ceramic particle-reinforced composites are determined by using differential thermal analysis (DTA) coupled with mathematical modeling. In applying this method, the cooling curves of the alloys and composites are first determined by using DTA, then mathematical modeling is used to simulate the cooling curves, and their solidification curves can thus be calculated. It has been found that the principal characteristics of the solidification curves of the composites and their matrix alloy are similar. The viscosities of these alloys and composites are determined by using a Searle-type viscometer. The viscosity of the semisolid slurry increases with increasing solid content. A sharp increase in the viscosity is observed during solidification, and the value of the critical solidified fraction is a function of the shear rate. Both the aluminum alloys and their respective composites displayed similar critical solidified fractions, and these values are hardly affected by the addition of the ceramic particles.     

Particle Size Effects of Silicon Carbide on Wear Behavior of SiC<Subscript>p</Subscript>-Reinforced Magnesium Matrix Composites

This article investigated the particle size effect of micro-sized SiC on the tribological behavior of SiC_p-reinforced AZ91D Mg-based metal–matrix composites (MMCs). The Mg MMCs were prepared by the melt-stirring technique for wear tests. The hardness and coefficient of friction of Mg MMCs increases as particle size of SiC particle in MMCs increases, except for the hardness tendency at the region between particle size of 11 and 15 μm. The SiC_p/AZ91D MMCs exhibit superior wear resistance under lower and moderate sliding condition. However, the effects of the SiC particle reinforcements on wear resistance are not as conclusive under severe sliding condition, since the matrix of MMCs were softened at elevated temperature under such a severe condition.