High-Strength and High-Fracture-Toughness Ceramics in the Al2O3/LaAl11O18 Systems

Control of microstructure in the Al₂O₃/LaAl₁₁O₁₈ system was performed. Elongated alumina grains were formed by doping with small addition of silica, and 20 vol% lanthana- luminate was formed in situ by the reaction of LaAlO₃- A1₂O₃ in an alumina matrix. Strengths of over 600 MPa and a high fracture toughness (6 MPa.m^1/2) were achieved in the material with both elongated A1₂O₃ grains and LaAl₁₁O₁₈ platelets. Generally antagonistic properties such as strength and fracture toughness have been made compatible in the same ceramic system.     

A novel agglomeration granulating system utilizing a centrifugal-fluidizing drive

Necessary conditions were studied for the optimum operation of agglomeration granulation. The mechanisms that would realize these conditions were investigated by several experiments.On the basis of the results obtained, a novel granulating system involving a surface wetness control mechanism has been developed.The present paper describes the mixing and dispersing characteristics of the coating vessel, the detection method for wetness control, the particular spraying units, and the operating conditions thereof, together with the characteristics of this newly developed powder coating granulation system.This system has been shown to provide an easy and reproducible granulating technique even when products below 1 mm in size are required.     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

Effects of Annealing on Dielectric Loss and Microstructure of Aluminum Nitride Ceramics

The effect of annealing on tan δ and microstructures of aluminum nitride (AlN) ceramics were explored. Yttria was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900°C for 2 h in a nitrogen flow atmosphere. In succession to sintering, AlN samples were annealed at 720, 970 and 1210°C for 2 and 4 h. Very low tan δ values between 2.6 and 6.0 × 10⁻⁴ at 28 GHz were obtained when the AlN samples were annealed for 4 h at all the annealing temperatures.     

Alteration of substrate specificity of cholesterol oxidase from Streptomyces sp. by site-directed mutagenesis

Despite the structural similarities between cholesterol oxidasefrom Streptomyces and that from Brevibacterium, both enzymesexhibit different characteristics, such as catalytic activity,optimum pH and temperature. In attempts to define the molecularbasis of differences in catalytic activity or stability, substitutionsat six amino acid residues were introduced into cholesteroloxidase using site-directed mutagenesis of its gene. The aminoacid substitutions chosen were based on structural comparisonsof cholesterol oxidases from Streptomyces and Brevibacterium.Seven mutant enzymes were constructed with the following aminoacid substitutions: L117P, L119A, L119F, V145Q, Q286R, P357Nand S379T. All the mutant enzymes exhibited activity with theexception of that with the L117P mutation. The resulting V145Qmutant enzyme has low activities for all substrates examinedand the S379T mutant enzyme showed markedly altered substratespecificity compared with the wild-type enzyme. To evaluatethe role of V145 and S379 residues in the reaction, mutantswith two additional substitutions in V145 and four in S379 wereconstructed. The mutant enzymes created by the replacement ofV145 by Asp and Glu had much lower catalytic efficiency forcholesterol and pregnenolone as substrates than the wild-typeenzyme. From previous studies and this study, the V145 residueseems to be important for the stability and substrate bindingof the cholesterol oxidase. In contrast, the catalytic efficiencies(k_cat/K_m) of the S379T mutant enzyme for cholesterol and pregnenolonewere 1.8- and 6.0-fold higher, respectively, than those of thewild-type enzyme. The enhanced catalytic efficiency of the S379Tmutant enzyme for pregnenolone was due to a slightly high k_catvalue and a low K_m value. These findings will provide severalideas for the design of more powerful enzymes that can be appliedto clinical determination of serum cholesterol levels and assterol probes.     

The effects of Ni and Li doping on the performance of lithium manganese oxide material for lithium secondary batteries

Layered Li_0.7[M_1/6Mn_5/6]O₂ (M=Li, Ni) was synthesized using a sol-gel method. P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor was first synthesized by a sol-gel method, and then O2-Li_0.7[M_1/6Mn_5/6]O₂ was prepared by an ion exchange of Li for Na in P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor. From charge/discharge curves, it was seen that Li_0.7[Li_1/6Mn_5/6]O₂ has two plateaus similar to those observed from a spinel structure, but Li_0.7[Ni_1/6Mn_5/6]O₂ holds a single plateau as observed from a typical layered structure. It was considered that Li_0.7[Li_1/6Mn_5/6]O₂ undergoes a phase transformation from layered to spinel structure during the charge/discharge cycle, but Li_0.7[Ni_1/6Mn_5/6]O₂ maintains O2-layered structure after the cycles. Li_0.7[Ni_1/6Mn_5/6]O₂ was higher in discharge capacity and retention rate than Li_0.7[Li_1/6Mn_5/6]O₂.     

Morphological study by TEM on uniaxially oriented thin films of PET, PEN and their blends

Uniaxially oriented thin films of poly(ethylene terephthalate) (PET), poly(ethylene 2,6-naphthalene dicarboxylate) (PEN) and their blends were prepared by applying shear strain to their respective melts, and the resulting morphologies were studied by transmission electron microscopy. Selected-area electron diffraction of each film revealed well-defined uniaxial orientation of polymer chains in the shearing direction. In the uniaxially oriented thin film of PEN, stacked-lamellar structure with the average long period of 27 nm consisting of a crystalline region about 15 nm thick and an amorphous one about 12 nm thick was found here and there in the dark-field image: PEN-type. On the other hand, stacked-lamellar structure was rarely observed in the case of PET: PET-type. In PET/PEN blends, the morphologies changed from the PET-type to the PEN-type with increasing content of PEN.     

A pre-heating vaporization technology of coal-water-slurry for the gasification process

A pre-heating vaporization technology of coal water slurry, CWS, was developed to increase the efficiency of coal gasification with the reduction of oxygen consumption. A CWS pre-heating experimental unit having a capacity of 2.0 tons-coal/day was manufactured. After the CWS was heated to 573 K at about 10 MPa, water in CWS was continuously vaporized in a tube of which the diameter increased gradually (2–10 mm I.D.), and dry coal particles with steam were atomized and fed to a vessel. No aggregation of coal particles was observed in the atomized samples. The temperature and the pressure distributions of the fluid were calculated with empirical heat transfer and pressure drop correlations. The calculated results well corresponded to the experimental data measured in some test points. Using the calculation model, a large scale apparatus of 100 tons-coal/day was designed using KNO₃ + NaNO₂ + NaNO₃ molten salt as a heating medium.     

Additional kernel observer: privilege escalation attack prevention mechanism focusing on system call privilege changes

International Journal of Information Security - Cyberattacks, especially attacks that exploit operating system vulnerabilities, have been increasing in recent years. In particular, if administrator...     

A Nom historical document recognition system for digital archiving

A Nom historical document recognition system is being developed for digital archiving that uses image binarization, character segmentation, and character recognition. It incorporates two versions of off-line character recognition: one for automatic recognition of scanned and segmented character patterns (7660 categories) and the other for user handwritten input (32,695 categories). This separation is used since including less frequently appearing categories in automatic recognition increases the misrecognition rate without reliable statistics on the Nom language. Moreover, a user must be able to check the results and identify the correct categories from an extended set of categories, and a user can input characters by hand. Both versions use the same recognition method, but they are trained using different sets of training patterns. Recursive X–Y cut and Voronoi diagrams are used for segmentation; k–d tree and generalized learning vector quantization are used for coarse classification; and the modified quadratic discriminant function is used for fine classification. The system provides an interface through which a user can check the results, change binarization methods, rectify segmentation, and input correct character categories by hand. Evaluation done using a limited number of Nom historical documents after providing ground truths for them showed that the two stages of recognition along with user checking and correction improved the recognition results significantly.