Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

课程群案例嵌入协同教学模式的探索

在课程群的教学中由于每门课程各自独立开展教学,缺乏知识的融合和衔接,导致学生运用综合知识解决问题的能力较弱。在课程群的教学中采用案例嵌入协同教学模式,将完整的工程案例嵌入到课程群各门课程的教学中,协同规划各门课程的教学任务,每门课程再围绕案例展开研究性教学。通过嵌入的工程案例衔接各门课程的知识点,帮助学生建构完整的知识体系,强化工程应用的概念；同时通过研究性教学,培养学生分析问题和解决问题的能力,两部分相结合,提高了学生运用综合知识解决复杂问题的能力。     

PCB废水总氮处理达标的工艺探讨

对PCB废水总氮的处理,从源头削减、分质收集、分质预处理到末端处理提出了多种方法,着重分析了MAP+管式微滤膜处理氨氮废水、多级组合式RO处理硝态氮废水和A2O+MBR处理综合废水,提出PCB废水总氮达标的组合工艺,项目建成后达到预期效果。     

Headspace fingerprinting approach to identify the major pathway influencing volatile patterns of vinasse-cured duck processed by high pressure,as well as its impact on physicochemical and sensory attributes

As a decisive attribute, flavour could be influenced by HP treatments through multiple physical and chemical pathways within the high pressure (HP)-assisted meat curing process. This investigation aimed to identify the major pathway influencing volatile flavour patterns of two representative vinasse-cured duck (VCD) products with HP treatments (150–300 MPa/15 min), including wet and dry types, by employing headspace fingerprinting as an untargeted approach. Results suggested that HP treatments greatly lowered moisture contents and increased Warner-Bratzler shear force and thiobarbituric acid reactive substances of the cured samples. According to multivariate models, the volatile flavour patterns of the HP-processed VCD could be clearly separated from the unprocessed samples, but the VCD pressurised at different intensities represented similar volatile fingerprinting, which was validated by e-nose analysis. The discriminant analysis (OPLS-DA) model outlined vinasse-derived ethanol, acetic acid, 3-methyl-1-butanol, 2-methyl-1-butanol, phenethyl alcohol and 2-methyl-3-octanone as the major discriminant aromas across the unpressurised and pressurised samples.     

Effects of structural characteristics on microwave dielectric properties of low-loss (Zn1-xNix)ZrNbTaO8 ceramics

Low-loss (Zn_1-xNi_x)ZrNbTaO₈ (0.02?≤?x?≤?0.10) ceramics possessing single wolframite structure are initiatively synthesized by solid-state route. Based on the results of Rietveld refinement, complex chemical bond theory is used to establish the correlation between structural characteristics and microwave performance in this ceramic system. A small amount of Ni²⁺ (x?=?0.06) in A-site with the fixed substitution of Ta⁵⁺ in B-site can effectually raise the Q?×?f value of ZnZrNb₂O₈ ceramic, embodying a dense microstructure and high lattice energy. The dielectric constant and τ_f are mainly affected by bond ionicity and the average octahedral distortion. The (Zn_0.94Ni_0.06)ZrNbTaO₈ ceramic sample sintered at 1150?°C for 3?h exhibits an outstanding combination of microwave dielectric properties: ε_r =?27.88, Q?×?f?=?128,951?GHz, τ_f =?–39.9?ppm/°C. Thus, it is considered to be a candidate material for the communication device applications at high frequency.