Investigation of charge transport mechanism in semiconducting La<Subscript>0.5</Subscript>Ca<Subscript>0.5</Subscript>Mn<Subscript>0.5</Subscript>Fe<Subscript>0.5</Subscript>O<Subscript>3</Subscript> manganite prepared by sol–gel method

Here in, we report the charge transport mechanism in semiconducting La_0.5Ca_0.5Mn_0.5Fe_0.5O₃ (LCMFO) polycrystalline material synthesized via sol–gel auto combustion route. X-ray diffraction (XRD) analysis confirmed the orthorhombic phase of the prepared material. Temperature dependent resistivity and impedance spectroscopy measurements have been carried out to probe the dielectric and electrical conduction mechanism which revealed a change of Mott variable range to the small polaronic hopping conduction mechanism around 303 K. The complex impedance and modulus spectra undoubtedly showed the contribution of both grain and grain boundary effect on the conduction properties of LCMFO. An equivalent circuit [(R_gbQ_gb) (R_gQ_g)] model has been used to address the electrical parameters associated with the different phases (grains and grain boundaries) having different relaxation times. The values of resistances of two phases obtained after fitting the equivalent circuit in the nyquist plot have been analyzed which confirmed the change of conduction mechanism around 303 K. The resultant change in conduction mechanism is also supported by the conductivity plots.     

Estimation of Desired Motion Intention and compliance control for upper limb assist exoskeleton

International Journal of Control, Automation and Systems - In this paper, we have addressed two issues for upper limb assist exoskeleton. 1) Estimation of Desired Motion Intention (DMI); 2) Robust...     

Steady flow of an Eyring Powell fluid over a moving surface with convective boundary conditions

In this article, the flow and heat transfer of Eyring Powell fluid over a continuously moving surface in the presence of a free stream velocity are investigated. Convective boundary conditions have been used in the problem formulation. The solution for velocity and temperature are computed by applying the homotopy analysis method (HAM). The effects of emerging fluid parameters (?), (δ) and Prandtl number (Pr) on the velocity and temperature are illustrated through graphs and tables for different values of λ. It is found that the boundary layer thickness is an increasing function of (?) and decreasing function of (δ). However the temperature and thermal boundary layer thickness decrease when the values of (?) and (δ) are increased.     

PtCo@NCNTs cathode catalyst using ZIF-67 for proton exchange membrane fuel cell

Zeolitic Imidazolate Frameworks (ZIF) is one of the potential candidates as highly conducting networks with large surface area with a possibility to be used as catalyst support for low temperature fuel cells. In the present study, highly active state-of-the-art PtCo@NCNTs (Nitrogen Doped Carbon Nanotube) catalyst was synthesized by pyrolyzing ZIF-67 along with Pt precursor under flowing ArH₂ atmosphere. The multi-walled NCNTs were densely grown on the surface of ZIF particles after pyrolysis. The high resolution TEM examination was employed to examine the nature of the PtCo particles as well as multi-walled NCNTs. Rotating disk electrode study was used for measuring oxygen reduction reaction performance for PtCo@NCNTs in 0.1 M HClO₄ and compared with commercial Pt/C catalyst. Fuel cell performance with PtCo@NCNT and commercial Pt/C catalysts was evaluated at 70 °C using Nafion-212 electrolyte using H₂ and O₂ gases (100% RH) and the observed peak power density of 630 and 560 mW cm^?2, respectively.     

Correlation of average diffuse and beam radiation with hours of bright sunshine

Empirical equations have been developed which correlate the monthly average daily horizontal diffuse and beam radiation with the fraction of maximum possible number of bright sunshine hours. These correlations are based on measured data from three widely spread Canadian stations.Depending upon whether or not the total horizontal radiation is known, the two correlations for the diffuse radiation are: .The correlation for beam radiation is: .     

Characterization of Ba4.5Re9Ti18O54 (Re = La,Nd) microwave dielectric ceramics

Ba_4.5Re₉Ti₁₈O₅₄ (Re = La, Nd) ceramics were prepared via a solid state mixed oxide route. X-ray diffraction (XRD) analysis revealed the formation of the major Ba_4.5Re₉Ti₁₈O₅₄ phase along with rutile (TiO₂) as a secondary phase. Rietveld structure refinement of the recorded XRD data confirmed that the crystal structure of Ba_4.5Nd₉Ti₁₈O₅₄ (BNT) was orthorhombic (Pnma) with unit cell parameters a = 22.3412 Å, b = 7.6824 Å and c = 12.1952 Å. Ba_4.5La₉Ti₁₈O₅₄ (BLT) exhibited high relative permittivity (95.6), low quality factor (2,102 GHz) and a high temperature coefficient of resonance frequency (+352 ppm/°C). The substitution of Nd for La caused a decrease in both the relatively permittivity and temperature coefficient of resonance frequency to 84.2 and 167 ppm/°C respectively and an increase in quality factor to 8,007 GHz. Raman spectroscopic analysis revealed that lattice defects may be responsible for the observed decrease in quality factor of BLT ceramics in comparison to BNT. The Raman shifts at 533.5 and 613.6 cm^?1, related to Ti–O bond stretching, decreased for BNT ceramics, which may be a possible reason for the observed decrease in relative permittivity.     

Performance of microwave synthesized dual solvent dope solution and lithium bromide additives on poly(ethersulfone) membranes

BACKGROUND: Generally the fabrication of polymeric membranes is a complicated and expensive process since it involves several steps. The preliminary preparation steps involve polymer drying and dissolution and is very time consuming and expensive. Currently, conventional electrothermal heating (CEH) is used to dissolve polyethersulfone in an aprotic solvent for membrane fabrication. Usually CEH requires 6 to 8 h at temperatures of 80 to 95 °C. This paper reports the fabrication and characterization of polyethersulfone (PES) asymmetric ultrafiltration membrane made from microwave (MW) synthesis casting solution consisting of various compositions of double solvents and lithium bromide (LiBr) additive. RESULTS: Homogeneous dual solvent dope solutions prepared via microware irradiation took only 1 h instead of the 7 h when prepared using CEH. The results also revealed that the membrane permeation and rejection rates, pore size and porosity were dependent on the ratio of LiBr to acetone. Membranes with LiBr kept at 2 and 3 wt% exhibited both high rejection and permeation rates with minimum pore sizes of 1.067 and 1.214 nm respectively. The presence of LiBr and the occurrence of chain scission were elucidated using Fourier transform infrared (FTIR) spectroscopy while its hydrophilic property was confirmed by water absorption and contact angle measurements. CONCLUSIONS: It was concluded that the microwave technique is capable of producing 1 L membrane solutions in less than 1 h. The membranes prepared from the microwave solutions show good rejection and permeation rates. Copyright © 2011 Society of Chemical Industry     

Current-mode active-only universal filter

A novel current-mode active-only universal filter based on and employing three DO-CCCIIs and two OAs is introduced. The circuit is fully integrable and programmable, and implements all the five generic filtering functions. The three basic filtering responses LP, BP and HP are implemented simultaneously by the circuit, while AP and notch signals can be realized simply by connecting appropriate node currents. The currents are available at high output impedances, so the synthesized filter can be cascaded without additional buffers to realize higher order filters. The filter performance factors ω ₀ and Q are electronically tunable in an orthogonal manner through separate bias currents of the CCCII. The PSPICE simulation was carried out to realize the proposed circuit.     

Vibrations of functionally graded cylindrical shells based on elastic foundations

In this paper, a study on the vibrations of functionally graded cylindrical shells based on the Winkler and Pasternak foundations is presented. The shell equations are amended by inducting the moduli of the Winkler and Pasternak foundations. The wave propagation method is employed to solve the shell dynamical equations. The method is based on the approximate eigenvalues of characteristic beam functions. The validity and accuracy of the present approach are verified by a number of comparisons.     

Laser sensor for detection of SF6 leaks in high powerinsulated switchgear systems

A novel photoacoustic spectrometer (PA) has been developed for in-situ detection of SF₆ leaks in low concentrations. The developed system is equipped with a sound alarm system and has been tested in the laboratory for very minute SF₆ leaks. This newly developed SF₆ detection device utilizes a high quality factor resonant photoacoustic cell and continuous wave (CW) line tunable CO₂ laser at 10.55 μm wavelength. Whenever SF₆ is detected an acoustic signal is generated and no signal appears from ambient air if there is no leakage of SF₆. An electret microphone is used for the detection of these acoustic signals. The system is capable of detecting leaks of the order of 3.5 ppbv (parts per billion by volume) concentration. This device has been proved to have significant applications to industrial organizations that have electric power gas insulated systems (GIS). It could be also applied for other applications such as monitoring of environmental pollutants with minimal adjustments