Improved-performance noncoherent weighted-coefficients diversity combiner for DPSK and NC-FSK signals in nonidentical Nakagami fading channels

It is well-known that noncoherent equal-gain combining (NC-EGC) is the simplest combining technique for noncoherent and differentially coherent communication systems. However, for nonidentical Nakagami-m channels (channels having nonuniform multipath intensity profile (MIP) and/or arbitrary non-integer fading parameters), the use of NC-EGC has three main disadvantages. First, its performance serves as a lossy upper bound to that of the optimum diversity combiner. Second, it results in complicated expressions for the system average error performance. Third, it incurs noncoherent combining loss (does not aid the use of diversity) at relatively low average signal-to-noise ratio (SNR). In this letter, we propose a modified version of the NC-EGC, which is a noncoherent combiner with weighting coefficients, to overcome the disadvantages of the conventional one. We show that this alternative combiner does provide improvements over the conventional N.C-EGC for all values of average SNRs, it does not incur any noncoherent combining loss, and it leads to a design of the receiver whose average error performance can be evaluated easily.     

Reversed Temperature-Dependent Propagation Delay Characteristics in Nanometer CMOS Circuits

The supply voltage to threshold voltage ratio is reduced with each new technology generation. The gate overdrive variation with temperature plays an increasingly important role in determining the speed characteristics of CMOS integrated circuits. The temperature-dependent propagation delay characteristics, as shown in this brief, will experience a complete reversal in the near future. Contrary to the older technology generations, the speed of circuits in a 45-nm CMOS technology is enhanced when the temperature is increased at the nominal supply voltage. Operating an integrated circuit at the prescribed nominal supply voltage is not preferable for reliable operation under temperature fluctuations. A design methodology based on optimizing the supply voltage for temperature-variation-insensitive circuit performance is proposed in this brief. The optimum supply voltage is 45% to 53% lower than the nominal supply voltage in a 180-nm CMOS technology. Alternatively, the optimum supply voltage is 15% to 35% higher than the nominal supply voltage in a 45-nm CMOS technology. The speed and energy tradeoffs in the supply voltage optimization technique are also presented     

High Rate Data Synchronization in GALS SoCs

Globally asynchronous, locally synchronous (GALS) systems-on-chip (SoCs) may be prone to synchronization failures if the delay of their locally-generated clock tree is not considered. This paper presents an in-depth analysis of the problem and proposes a novel solution. The problem is analyzed considering the magnitude of clock tree delays, the cycle times of the GALS module, and the complexity of the asynchronous interface controllers using a timed signal transition graph (STG) approach. In some cases, the problem can be solved by extracting all the delays and verifying whether the system is susceptible to metastability. In other cases, when high data bandwidth is not required, matched-delay asynchronous ports may be employed. A novel architecture for synchronizing inter-modular communications in GALS, based on locally delayed latching (LDL), is described. LDL synchronization does not require pausable clocking, is insensitive to clock tree delays, and supports high data rates. It replaces complex global timing constraints with simpler localized ones. Three different LDL ports are presented. The risk of metastability in the synchronizer is analyzed in a technology-independent manner     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Experimental evidence of a relationship between monomer plasma residence time and carboxyl group retention in acrylic acid plasma polymers

Decreasing carboxyl retention in deposits from the glow region of an acrylic acid plasma was measured by X-ray photoelectron spectroscopy and chemical derivatisation as the collection distance from the monomer vapour inlet was increased. Volatilisation of plasma polymerised acrylic acid was detected after trifluoroethanol derivatisation; this is correlated with evaporation of low molecular weight components observed previously.     

Ambient Technology — Now You See It, Now You Don't

The continuing progression of Moore's Law has enabled the miniaturisation and dramatic cost reduction in electronics over the last ten years. For a truly pervasive communications environment the challenges of hiding key hardware technologies from the user are rapidly being overcome. This paper reviews the status of these hardware technology developments in the pervasive space and briefly discusses other contributing factors that will enable the pervasive vision to be realised.     

Smooth profile generation for a tile printing machine

In this paper a digital filter is proposed for the generation of smooth set points for motion control systems. The proposed nonlinear filter produces profiles with bounded velocity and acceleration starting from rough reference signals (steps and ramps). An actual implementation of the filter for a tile printing machine is presented and experimental results are reported.     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

Three takes on telecom's troubles

Spectrum asked three IEEE members from the telecommunications sector to comment on the industry's current woes and prospects. Roch Guerin discusses bandwidth as a commodity and how to deal with it. The impact of technological change on telecommunications is enormous and calls for a shift in business models. Technology is making bandwidth a commodity and it should not matter who supplies it. Competition is vital and commodity providers must be decoupled from value providers. Frank Ferrante points out that the Year 2000 crisis resulted in manufacturers being deluged with orders for new upgraded systems. Vast sums were spent to meet the demand in time. However, when Y2K was over, production stayed high and inventories continued to build, while demand effectively stopped overnight. Dazzling new innovations are needed to compel the masses to spend and manufacturers must apply their resources to deliver quickly and efficiently. Jules A. Bellisio discusses the role of engineers in bringing new ideas to the market place. Many engineers have put together ventures for the sole purpose of attracting capital. The underlying technology and business propositions were there solely to lure the unsuspecting. By allowing engineers to use technology simply to cover for a scam, then the profession is also to blame for the current problems.