Structure and properties of nanocomposites based on poly(butylene succinate) and organically modified montmorillonite

Poly(butylene succinate) and organically modified montmorillonite nanocomposites with there different compositions were prepared via melt blending in a twin‐screw extruder. The structure of the nanocomposites was studied with X‐ray diffraction and transmission electron microscopy, which revealed the formation of intercalated nanocomposites, regardless of the silicate loading. Dynamic mechanical analysis revealed a substantial increase in the storage modulus of the nanocomposites over the entire temperature range investigated. The tensile property measurements showed a relative increase in the stiffness with a simultaneous decrease in the yield strength in comparison with that of neat poly(butylene succinate). The oxygen gas barrier property of neat poly(butylene succinate) improved after nanocomposite preparation with organically modified montmorillonite. The effect of the layered‐silicate loading on the melt‐state linear viscoelastic behavior of the intercalated nanocomposites was also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 777–785, 2006     

Synthesis of tetramethyl-p-silphenylenesiloxanedimethylsiloxane triblock copolymer by employing living anionic polymerization

Dimethylsiloxane-tetramethyl-p-silphenylenesiloxane-dimethylsiloxane (DMS-TMPS-DMS) triblock copolymer was synthesized by employing living anionic polymerization of hexamethylcyclotrisiloxane (D₃). Two synthetic methods were carried out for the polymerization. One of those methods was the anionic polymerization of D₃ initiated at the silanolate anion which was prepared from the terminal hydroxyl group of silanol-terminated TMPS prepolymer by reaction with n-butyllithium (method 1). The other was the coupling reaction of vinyl-terminated TMPS prepolymer with hydrosilyl-terminated DMS prepolymer obtained from the anionic polymerization of D₃ by using diphenylmethylsilanolate anion as initiator (method 2). In method 1, DMS contents of the copolymers ranged from 25.8 to 72.5 wt% and the values agreed with the ratio of D₃ to TMPS prepolymer. The weight-average molecular weights ranged from 1.36×10⁴ to 19.4×10⁴ and were close to the predicted values calculated from the $\text{M}\text{?}{}_{\mathrm{v}}$ of the TMPS prepolymer and the amount of D₃ added. In the case of method 2, weight-average molecular weights ranged from 19.5×10⁴ to 24.2×10⁴. The high molecular weight copolymer could thus be obtained by method 2. Intrinsic viscosity values of the triblock copolymers agreed with calculated values obtained by considering the copolymer as a binary mixture of these homopolymers. Differential scanning calorimetry and thermogravimetry were carried out on the triblock copolymers. The equilibrium melting temperatures of each of the copolymers were very close to that of poly-TMPS (160°C). The glass transition temperature and heat of fusion were decreased as the DMS content was increased. The thermogravimetric curves for the copolymers indicated that the thermal stability of the triblock copolymer was intermediate between the DMS and TMPS homopolymers.     

Oligomer-Rich Fraction from Polydisperse Sample of Poly(bis(β-phenoxyethoxy)phosphazene)

Poly[bis(-phenoxyethoxy)phosphazene] [PBPEP] had been shown in our previous paper to be a very useful polymer for investigating the crystallization mechanism of polymers, as the crystallization rate of PBPEP is extraordinarily small when isothermally crystallized from the melt. The crystallization of the low molecular weight oligomers of PBPEP was first studied in comparison to the high molecular weight polymers. The oligomer-rich fraction was obtained by fractionation of the as-polymerized sample, which had a broad molecular weight distribution. The fractions thus obtained were characterized by solution viscometry and size exclusion chromatography. The melting temperature and the growth rate of the spherulite from the melt were investigated by differential scanning calorimetry and optical microscopy. The growth rate was one or two orders of magnitude smaller in the oligomer-rich fraction than in the other high molecular weight fractions. A collapsed spherulite appeared in the oligomer-rich fraction at high crystallization temperatures. It is speculated that in the oligomer-rich fraction there is an excess free energy due to defects in the crystal phase. This defect is considerably larger in the oligomer-rich fraction than in the other fractions because a large quantity of short length chains is present.     

Prediction of the biologically active sites in eclosion hormone from the silkworm, Bombyx mori

The structure-activity relationship of eclosion hormone from the silkworm, Bombyx mori, was analyzed. First, the probable active residues in silkworm eclosion hormone and also tobacco hornworm eclosion hormone were predicted by the average distance map method. To examine the contributions of those residues to the activity of silkworm eclosion hormone, Gly-substituted mutants for those predicted residues were produced by site-directed mutagenesis and their activities were evaluated by a bioassay. Finally, Glu12, Met24 and Phe25 were estimated to be the crucial residues for the eclosion hormone activity. The possibility of the development of a blocker of an eclosion hormone receptor on the basis of the present work is also discussed.      

Optimization of the sputter-deposited platinum cathode for a direct methanol fuel cell

The electrodes prepared by a sputtering method were evaluated as the cathodes for direct methanol fuel cells (DMFCs). Pt loading below 0.25 mg cm⁻² achieved higher mass activities than that of 0.5 mg cm⁻² prepared by the paste method, which was general conventional method. However, an increase in Pt loading reduced the catalyst activity for the oxygen reduction reaction (ORR). This result may suggest an increase in only electrochemically inactive Pt. Pt utilization efficiency can be found about ten times higher at Pt loading of 0.04 mg cm⁻². Moreover, addition of Nafion to sputter-deposited Pt cathodes is found possible to improve the catalyst activity for the ORR, but the excess Nafion over the optimum condition reduces the active sites.     

Preparation of plasma-polymerized membranes from I-(trimethylsilyl)-I-propyne and gas permeability through the membranes

Summary Plasma-polymerized membranes for gas separation were prepared from 1-(trimethylsilyl)-1-propyne. The permeation data of He, H₂ 0₂, N₂, CO₂, and CH₄ through the membranes showed plasma-polymerized 1-(trimethylsilyl)-1-propyne had high permselectivity but low permeability compared with poly[l-(trimethylsilyl)-1-propyne]. This behavior is considered to be due to the crosslinking structure of the plasma-polymerized membrane. The correlation between plasma polymerization conditions and the membrane performance was studied. The optimum condition at which the deposition rate of the plasma polymer is maximized agreed with the optimum value to yield maximum separation factor of gases through the membrane.     

Temperature Dependence of Young's Modulus and Internal Friction in Alumina, Silicon Nitride, and Partially Stabilized Zirconia Ceramics

The temperature dependence of Young's modulus and internal friction (Q⁻¹)in alumina, silicon nitride, and partially stabilized zirconia (Y-PSZ) ceramics was studied. Little change in Q⁻¹ was found for alumina, whereas Q⁻¹ for silicon nitride ceramics increased above 700°C. The Q⁻¹ of Y-PSZ increased markedly with increasing temperature up to a peak at ∼200°C.     

Reaction products of α-tocopherol with methyl linoleate-peroxyl radicals

α-Tocopherol was reacted with methyl linoleateperoxyl radicals at 37°C. The peroxyl radicals were generated by the reaction of methyl linoleate with a free radical initiator, 2,2′-azobis(2,4-dimethylvaleronitrile). The primary products of α-tocopherol with methyl linoleate-peroxyl radicals were isolated by reversephase and normal-phase high performance liquid chromatography (HPLC), and their structures were characterized by ultraviolet (UV), infrared (IR),¹H and¹³C nuclear magnetic resonance (NMR) and mass spectrometry (MS). There were four stereoisomers of methyl 13-(8a-peroxy-α-tocopherone)-9(Z),11(E)-octadecadienoate and four stereoisomers of methyl9-(8a-peroxy-α-tocopherone)-10(E),12(Z)-octadecadienoate.     

Synthesis and properties of novel side-chain-sulfonated polyimides from bis[4-(4-aminophenoxy)-2-(3-sulfobenzoyl)]phenyl sulfone

A novel side-chain-sulfonated aromatic diamine of bis[4-(4-aminophenoxy)-2-(3-sulfobenzoyl)]phenyl sulfone (BAPSBPS) was synthesized. Sulfonated copolyimides were synthesized by random and sequenced block copolymerization of 1,4,5,8-naphthalene tetracarboxylic dianhydride, BAPSBPS and nonsulfonated diamine. They displayed good solubility in common aprotic solvents and high desulfonation temperature of 350 °C, suggesting the high stability of sulfonic acid groups. The reduced viscosity was in the range of 0.4-1.8 dl/g at 0.5 g/dl and 35 °C. Flexible and tough membranes with reasonably high mechanical strength were prepared. They showed anisotropic membrane swelling with larger swelling in thickness than in plane. They displayed reasonably high proton conductivity (σ), taking their lower ion exchanging capacity (IEC) into account. For example, the membrane with IEC of 1.54 mequiv/g showed σ values of 81 and 11 mS/cm in water and 70% RH, respectively, at 60 °C.     

Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004