On the behavior of microstructures with multiple length scales

The current study aims to provide fundamental insight into the behavior of microstructures containing grain sizes that span multiple length scales. A commercial 5083 Al alloy was selected as the material of interest to facilitate comparison with recently published data. The materials studied here were prepared via the thermal consolidation of powders that were cryomilled for different times (i.e., 0, 2, 4, and 8 hours). Following consolidation, the resultant microstructure was characterized by an equiaxed grain morphology with a size distribution centered around 200∼300 nm. Dispersed among the 200- to 300-nm grains were coarse-grained regions or ligaments with a grain size ranging from 600 nm to 2 μm. The occurrence of coarse-grained regions is rationalized on the basis of recrystallization or subgrain coarsening, whereas the occurrence of equiaxed fine regions is proposed to be a result of continuous grain growth. Two types of microstructures were selected for study, containing coarse-grained volumes of approximately 28 pct and 43 pct that corresponded to an ultimate tensile strength (UTS) of 566 MPa and 535 MPa, and a fracture strain of 3.2 pct and 3.5 pct, respectively. The observed ductility and the relevant toughening mechanisms were discussed in light of the presence of multiple length scales.     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.     

Optical signal routing using emission packet positioning of semiconductor heterostructure

We present a novel optical switching technique utilizing emission packet positioning of semiconductor heterostructure. A modulation-doped p-AlGaAs-GaAs heterostructure is employed to control spontaneous emission packet positioning with electric fields. Emission packets generated by optical input signals are brought over 150 /spl mu/m with electric fields, so the output fibers can detect the emission intensity as signals. The first-order analysis indicates that the drift velocity of minority electrons in GaAs limits the detectable maximum data rate and nanoseconds timescale signal routing operation at 20 Gb/s is possible at an electron drift velocity of 2/spl times/10/sup 7/ cm/s.     

泥土中微量六氯环戊二烯的气相色谱分析

采用SE 3 0为固定液进行色谱柱分离 ,用外标定量法测定泥土中的微量六氯环戊二烯 ,结果最小检知量为 0 .18× 10 - 6 ,相关系数为 0 .99992。     

东营凹陷南斜坡储集层成岩作用及对储集性能的影响

东营凹陷南斜坡孔店组岩石类型以岩屑长石砂岩为主 ,长石砂岩和岩屑砂岩次之 ,其中岩屑长石砂岩含量超过 90 %。砂岩成岩作用包括压实作用、胶结作用、溶蚀作用、交代作用等 ,其中胶结作用使储层原生孔隙迅速变差 ,而溶蚀作用是次生空隙发育的主要因素。孔店组砂岩成岩作用进入晚成岩A期 ,期间经历了早成岩A期、B期。影响成岩作用的主要因素为构造演化背景、岩石成分、沉积环境、孔隙流体性质等。     

Measurement of gain spectrum for Fabry-Perot semiconductor lasers by the Fourier transform method with a deconvolution process

To improve the accuracy of measured gain spectra, which is usually limited by the resolution of the optical spectrum analyzer (OSA), a deconvolution process based on the measured spectrum of a narrow linewidth semiconductor laser is applied in the Fourier transform method. The numerical simulation shows that practical gain spectra can be resumed by the Fourier transform method with the deconvolution process. Taking the OSA resolution to be 0.06, 0.1, and 0.2 nm, the gain-reflectivity product spectra with the difference of about 2% are obtained for a 1550-nm semiconductor laser with the cavity length of 720 /spl mu/m. The spectra obtained by the Fourier transform method without the deconvolution process and the Hakki-Paoli method are presented and compared. The simulation also shows that the Fourier transform method has less sensitivity to noise than the Hakki-Paoli method.     

Obtaining shorter regular expressions from finite-state automata

We consider the use of state elimination to construct shorter regular expressions from finite-state automata (FAs). Although state elimination is an intuitive method for computing regular expressions from FAs, the resulting regular expressions are often very long and complicated. We examine the minimization of FAs to obtain shorter expressions first. Then, we introduce vertical chopping based on bridge states and horizontal chopping based on the structural properties of given FAs. We prove that we should not eliminate bridge states until we eliminate all non-bridge states to obtain shorter regular expressions. In addition, we suggest heuristics for state elimination that leads to shorter regular expressions based on vertical chopping and horizontal chopping.     

Numerical modelling for scattering of waves in three-dimensional cracked material

In this paper, a mathematical model is proposed for the problem of the scattering of plane waves in a three-dimensional cracked materials. Instead of obtaining closed-form solutions as in conventional theoretical analysis methods, this approach, called the Equivalent Nodal Force (ENF) method formulates the mechanical effects of cracks as an equivalent nodal force in a numerical procedure, and physically translates cracked material into an equivalent continuous one. Several mechanical relations between waves and cracks are evident from this method. Also the results of several numerical calculations are presented and these are compared with those obtained by the conventional methods.     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。