基于图像增强的去雾快速算法的FPGA实现

基于图像增强方法，本文提出了一种使用亮度映射的图像去雾快速算法。此算法通过调整室外多雾场景图像的对比度，提高了雾中物体的辨识度。算法的复杂度低、处理延迟小，实时性高，利于FPGA的实现。实现时不需外存储器，延时为ns级，并提供了强度调节接口，以适应较广的应用环境。     

基于DTW改进算法的孤立词识别系统的仿真与分析

传统的DTW算法在进行孤立词语音识别时着重于时间规整和语音测度的计算，而没有对数据的可靠性和有效性进行分析。本文提出了一种改进的端点检测算法，并采用一种改进的DTW算法，在计算机上进行了仿真。实验结果表明采用改进后的DTW算法有效的降低了识别时间和存储数据量，提高了系统性能。     

一种新型注入剖面组合测井仪及其应用

为了提高注入剖面测井的准确性，研制了一种新型注入剖面组合测井仪。该仪器由流量处理单元、伽马处理单元、井温处理单元、磁性定位处理单元、调制式传输、电源电路六部分组成。一次下井可同时测取流量、伽马、井温、磁性定位四组参数。具有测取资料精度高、单芯电缆传输、流量可单点测量也可连续测量以厦现场监测和维修方便等特点。     

Multi-level attention model for tracking and segmentation of objects under complex occlusion

A multi-level attention framework for tracking and segmentation of humans and objects under complex occlusions is investigated, featuring an effective probabilistic appearance-based technique for pixel reclassification during object grouping and splitting. A novel ’spatial-depth affinity metric’ is introduced in the conventional likelihood function, utilising information of both spatial locations of pixels and dynamic depth ordering of the component objects in grouping. Depth ordering estimation is achieved through a combination of top-down and bottom-up approach. Experiments on some realworld difficult scenarios of low quality and highly compressed videos demonstrate the very promising results achieved.     

家具制造技术进展

21世纪以来，随着全球经济的发展．家具业的增长十分迅速．国际家具生产总值已超过2500亿美元。发达的家具业大量应用了新材料．在制造及其控制过程中采用了现代计算机技术和信息技术手段．使这个传统产业跻身于现代产业之列。由于家具是人们生活和工作须臾不能离开的器具．它必将以不断改进的结构和日益增多的功能来满足人类的需要．改善人类生活的品质。因此．家具产业将持续以勃勃生机，与人类社会共同进步和发展。     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

Ad Hoc与无线网络的扩展性研究

Ad Hoc作为无线网络的具有高抗毁性和灵活性的扩展网络,日益引人关注。本文首先从环绕网的理念入手,介绍Ad Hoc作为现有无线网络扩展的意义和优势,然后重点分析并提出融合策略以及需要思考的问题。     

全球3G市场管制政策分析

主要对各国3G许可证与使用技术标准的抽绑政策．各国对2G／3G网络漫游的管制规定。以及3G网络之间共享的种类及实施方式等方面做了详尽的讲解，并进行比较和分析。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry