A mathematical model for platinum/ PTFE/porous nickel fuel cell oxygen diffusion electrodes

This paper describes the cylindrical agglomerate model for oxygen/alkali gas diffusion electrodes fabricated from platinum, PTFE and porous nickel. Corrections for the increase in hydroxyl ion concentration with increasing current density have been made to the original model of Brown and Horve. Changes in performance by variation of the bulk structural parameters, e.g. agglomerate radius, porosity and tortuosity, have been studied. Theoretical modes of electrode decay have been explored.List of symbols Transfer coefficient - C Concentration of O₂ in elec trolyte mol cm^–3 - C _i Concentration of O₂ atr = R mol cm^–3 - C _o Concentration of O₂ in electrolyte atr = mol cm^–3 - Diffusion coefficient of O₂ in KOH cm² sec^–1 - Film thickness cm - E Overpotential of the electrode V - F Faraday's constant - i Electrode current density A cm^–2 - i _a Current per agglomerate A - I ₁(Z) First order Bessel function - I ₀(Z) Zero order Bessel function - j Local current density A cm^–2 - j _o Exchange current density A cm^–2 - L Agglomerate length (catalyst thickness) cm - N Number of electrons in rate determining step - N _a Number of agglomerates per cm² of electrode - Potential drop along ag glomerate V - _L Potential drop at L_a V - r Radial direction - R Radius of agglomerate cm - R _o Gas constant - Density of platinum g cm^–3 - S _g Surface area per gram cm² g^–1 - Solubility coefficient of O₂ mol cm^–3 - _m Electrolyte conductivity (ohm cm)^–1 - T Absolute temperature °K - _a Axial tortuosity - Porosity of platinum in the agglomerate - _r Aadial tortuosity of the agglomerate - W Catalyst loading g cm^–2 - x Axial direction     

Modified Indigo Method For Gaseous And Aqueous Ozone Analyses

The indigo method developed by Bader and Hoigné for aqueous ozone analysis was modified to allow for both gaseous and aqueous ozone determination. Gas or water samples were extracted with a gas-tight syringe containing a known volume of indigo reagent. The modified procedure provided a more consistent basis for gaseous and aqueous ozone determination allowing for more accurate ozone mass balance calculations. Direct gaseous ozone UV absorbance with molar absorptivity of 3,000 M^?1cm^?1 at 258 nm was used as primary standard to determine the molar absorptivity of the indigo reagent. The molar absorptivity of indigo reagent, assuming a 1:1 stoichiometric ratio for the reaction between indigo and ozone, was determined to be 23,150 ± 80 M^?1cm^?1, or approximately 16 percent higher than that of 20,000 M^?1cm^?1 suggested by Bader and Hoigné. An independently calibrated membrane-electrode ozone monitor showed good correlation with indigo method results using the molar absorptivity value determined in this study. The apparent molar absorptivity of aqueous ozone at the wavelength of 258 nm measured by the modified indigo method increased from 2,400 to 3,600 M^?1cm^?1 in the investigated ozone concentration range of 0.4 to 11.0 mg/L. This variation might have been caused by the inherent interference of unidentified ozone byproducts, which presence was supported with scanning spectra in the wavelength range of 200 to 300 nm.     

Polyurethane‐infiltrated carbon foams: A coupling of thermal and mechanical properties

The thermal and mechanical properties of polyurethane‐infiltrated carbon foam of various densities were investigated. By combining the high thermal conductivity of the carbon foam with the mechanical toughness of the pure polyurethane, a mechanically tough composite (relative to the unfilled foam) that could be used at higher temperatures than the polyurethane's degradation was formed. Both the tensile strength and the modulus increased by an order of magnitude for the composites compared to unfilled foam, while the compressive and shear strengths and moduli of the composites approached values exhibited by pure polyurethane. At both 300 and 400°C, the rectangular blocks of pure polyurethane lost their mechanical integrity due to decomposition in air. Thermogravimetric analysis confirms substantial initial weight loss above 290°C. Filled carbon foam blocks, however, maintain their mechanical integrity at both 300 and 400°C indefinitely, although the bulk of the rectangular block mass is polyurethane. Three different carbon foam densities are examined. As expected, the higher density foams show greater heat transfer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2348–2355, 2003     

Processing, Microstructure, and Wear Behavior of Silicon Nitride Hot-Pressed with Alumina and Yttria

Commercial silicon nitride powder with A1₂O₃ and Y₂O₃ additives was hot-pressed to complete density. The resulting microstructure contained elongated grains with no trace of remaining α-Si₃N₄. The aspect ratio of the elongated grains increased with increasing soak time at a fixed hot-pressing temperature. X-ray diffraction analysis showed that the crystalline phase in the hot-pressed samples was β-sialon (Si_6−zAl_zO_zN_8−z) with z values that increased with soak time. The fracture strength and fracture toughness of the samples increased as the aspect ratio of the grains increased. The Vickers hardness decreased slightly as the soak time was increased, which was attributed to a grain size effect. Wear tests of silicon nitride against silicon nitride were conducted on a reciprocating pin-on-disk apparatus with paraffin oil as a lubricant. Correlation studies of wear with microstructure and mechanical properties were performed. The wear rate increased rapidly with increasing soak time in spite of the increased strength and toughness. This was attributed to increased third-body wear caused by pullout of pieces from the wear surface. The pullout mechanism was not conclusively identified. However, TEM examination showed clear evidence of dislocation motion under the wear scar. Grain boundary microstresses caused by the anisotropic thermal expansion and elastic properties of the elongated grains may have contributed to the observed pullout.     

FLUID SHEET THICKNESS AND VELOCITY AT THE TIP OF A BLACK LIQUOR SPLASHPLATE NOZZLE

The fluid sheet thickness and velocity at the tip of a spray nozzle have previously been identified as being important to the ultimate droplet size distribution. In this investigation both the fluid sheet thickness and the velocity of the top surface just beyond the rim of a splashplate nozzle have been measured as functions of nozzle exit velocity and fluid viscosity. Measurements were made on two Babcock & Wilcox Co. splashplate nozzles, a 12-49 and a 15-52, specifically designed for black liquor, a by-product of wood pulping. Comparisons of the ratio of the sheet velocity to the nozzle velocity are shown to be very similar to previous data for the ratio of droplet velocity to nozzle velocity. Likewise, the dependence of the sheet thickness on nozzle exit velocity closely matches the previously measured dependence of the ultimate median droplet size on nozzle exit velocity. Both of these results are consistent with current theories of droplet formation mechanisms. Analysis of continuity and viscous drag on the splashplate are used to develop correlation equations for the data     

Restoration of depressed prostanoid-induced ileal contraction in spontaneously hypertensive rats by dietary fish oil

We have reported that dietary fish oil (FO) rich in n-3 PUFA modulates gut contractility. It was further demonstrated that the gut of spontaneously hypertensive rats (SHR) has a depressed contractility response to prostaglandins (PG) compared with normotensive Wistar-Kyoto (WKY) rats. We investigated whether feeding diets supplemented with n-3 PUFA increased gut contractility and restored the depressed prostanoid response in SHR gut. Thirteen-week-old SHR were fed diets containing fat at 5 g/100 g as coconut oil (CO), lard, canola oil containing 10% (w/w) n-3 FA as alpha-linolenic acid (1 8:3n-3), or FO (as HiDHA, 22:6n-3) for 12 wk. A control WKY group was fed 5 g/100 g CO in the diet. As confirmed, the SHR CO group had a significantly lower gut response to PGE2 and PGF2alpha compared with the WKY CO group. Feeding FO increased the maximal contraction response to acetylcholine in the ileum compared with all diets and in the colon compared with lard, and restored the depressed response to PGE2 and PGF2alpha in the ileum but not the colon of SHR. FO feeding also led to a significant increase in gut total phospholipid n-3 PUFA as DHA (22:6n-3) with lower n-6 PUFA as arachidonic acid (20:4n-6). Canola feeding led to a small increase in ileal EPA (20:5n-3) and DHA and in colonic DHA without affecting contractility. However, there was no change in ileal membrane muscarinic binding properties due to FO feeding. This report confirms that dietary FO increases muscarinic- and eicosanoid receptor-induced contractility in ileum and that the depressed prostanoid response in SHR ileum, but not colon, is restored by tissue incorporation of DHA as the active nutrient.     

Microstructure of high modulus solid state extruded polyethylene: 2. X-ray scattering studies of 12, 24 and 36 extrusion draw ratio

The microstructure of a series of solid state extruded polyethylene fibres was examined by wide- and small-angle X-ray scattering. By measuring absolute intensities using a two dimensional position sensitive detector, accurate values of the small-angle invariant for anisotropic samples were obtained. This measurement coupled with wide-angle X-ray scattering and d.s.c. permitted determination of the density of the noncrystalline component. The use of a two phase model for solid state extruded polyethylene is justified if consideration is given to the effective densities of the crystalline and noncrystalline phases, which change with deformation. The effective density of the crystalline phase decreases by 1% (0.999–0.990 g cm^?3) from the unextruded billet compared to a 36 draw ratio extrudate, while the noncrystalline phase density increases by 6% (0.84–0.89 g cm^?3). These changes lead to an overall decrease in the mean squared electron density fluctuation of 63%. The average axial crystallite length measured by wide-angle X-ray scattering increases with extrusion draw ratio while the SAXS long period decreases and weakens considerably. These observations and the electron microscopy results from the previous paper, (Polymer, 1982, 23, 1069), are fully consistent with the key features of the Peterlin model of fibre microstructure.     

The Effect of Temperature on the Strength of Adhesively-Bonded Composite-Aluminium Joints

Different materials have different coefficients of thermal expansion, which is a measure of the change in length for a given change in temperature. When different materials are combined structurally, as in a bonded joint, a temperature change leads to stresses being set up. These stresses are present even in an unloaded joint which has been cured at say 150°C and cooled to room temperature. Further stresses result from operations at even lower temperatures.

In addition to temperature-induced stresses, account also has to be taken of changes in adhesive properties. Low temperatures cause the adhesive to become more brittle (reduced strain to failure), while high temperatures cause the adhesive to become more ductile, but make it less strong and more liable to creep.

Theoretical predictions are made of the strength of a series of aluminium/CFRP joints using three different adhesives at 20°C and 55°C. Various failure criteria are used to show good correlation with experimental results.     

Thermodynamic measurements in magnetically ordered solid3He

Measurements of the melting pressure and constant-volume pressure of solid³He have been made in the vicinity of the various magnetic-ordering transitions. Data have been obtained at several magnetic fields for both the low-field phase and the high-field phase, with particular attention given to the region of the polycritical point. The absence of a latent heat indicates that the transition from the paramagnetic to the high-field phase is second order or type. A spin-wave velocity of 6.95 cm/sec was obtained from theT ⁴ temperature dependence of the melting pressure in the high-field phase forB=0.495 T. These data provide the entropy and volume discontinuities as functions of field along the first-order low-field phase boundary. The volume dependence of the transition temperatures has been extracted from these and other data.     

An exploratory study of api changes and usages based on apache and eclipse ecosystems

Frameworks are widely used in modern software development to reduce development costs. They are accessed through their Application Programming Interfaces (APIs), which specify the contracts with client programs. When frameworks evolve, API backward-compatibility cannot always be guaranteed and client programs must upgrade to use the new releases. Because framework upgrades are not cost-free, observing API changes and usages together at fine-grained levels is necessary to help developers understand, assess, and forecast the cost of each framework upgrade. Whereas previous work studied API changes in frameworks and API usages in client programs separately, we analyse and classify API changes and usages together in 22 framework releases from the Apache and Eclipse ecosystems and their client programs. We find that (1) missing classes and methods happen more often in frameworks and affect client programs more often than the other API change types do, (2) missing interfaces occur rarely in frameworks but affect client programs often, (3) framework APIs are used on average in 35 % of client classes and interfaces, (4) most of such usages could be encapsulated locally and reduced in number, and (5) about 11 % of APIs usages could cause ripple effects in client programs when these APIs change. Based on these findings, we provide suggestions for developers and researchers to reduce the impact of API evolution through language mechanisms and design strategies.