Viscometric studies of starch-g-polyacrylamide composites

Composites of starch-g-polyacrylamide, starch, and polyacrylamide have been prepared by gamma radiation-initiated polymerization of acrylamide in the presence of starch in aqueous medium. The polymerization was studied as a function of the (i) amount of water (ii) monomer concentration, and (iii) total dose. The optimum conditions for maximum conversion of the monomer to homopolymer and graft copolymer have been evaluated. Percentage of grafting of polyacrylamide could not be determined precisely as both the homopolymer and the graft are soluble in common solvents and all attempts to separate the graft from the homopolymer were unsuccessful. However, the formation of the starch-g-polyacrylamide copolymer was confirmed by the turbidimetric studies using acetone as a nonsolvent. The products of polymerization of acrylamide in the presence of starch consisted of unreacted starch, starch-g-polyacrylamide, and polyacrylamide and is referred to as the composite. Acrylamide was also polymerized in the absence of starch using γ-rays as means of initiation and the optimum conditions for maximum conversion of acrylamide to polyacrylamide have been evaluated. Viscosity behavior of the composite and polyacrylamide was studied in aqueous medium at 30±0.04°C. The reduced specific viscosity of the aqueous solution of acrylamide and the composite as well was found to increase with increasing dilution, the effect being more pronounced in the composite. This tends to indicate that both the homopolymer and the composite behave as polyelectrolytes. An attempt has been made to explain the polyelectrolytic behavior of the homopolymer and the composite. © 1993 John Wiley & Sons, Inc.     

Occurrence of wax esters and 1-O-alkyl-2,3-diacylglycerols in goat epididymal sperm plasma membrane

Two unusual lipid classes were detected by thin-layer chromatography in the neutral lipids derived from goat cauda-epididymal sperm plasma membrane. The lipids were identified as wax esters and 1-O-alkyl-2,3-diacylglycerols based on chromatographic properties, identity of their hydrolysis products, and infrared/¹H nuclear magnetic resonance spectral evidence. The membrane containedca. 3 and 5 μg/mg protein of wax esters and alkyldiacylglycerols, respectively. The relative proportions of wax esters and alkyldiacylglycerols in the total neutral lipids were 1.5% and 2.4%, respectively. The lipids contained fatty acids with chain lengths of C₁₄ to C₂₂. The major fatty acids of the wax esters were 14∶0, 16∶0, 16∶1ω7, 18∶0 and 18∶1ω9. The fatty acids in alkyldiacylglycerol were 16∶0, 18∶0, 22∶5ω3 and 22∶6ω3. Alkyldiacylglycerol was particularly rich in docosahexaenoic acid 22∶6ω3) representing 30% of the total fatty acids. The alcohols of wax ester were all saturated with C₂₀–C₂₉ carbon chains. The deacylated products derived from alkyldiacylglycerols were identified as hexadecyl, octadecyl and octadec-9′-enyl glycerol ethers.     

Ion-solvent interaction from viscosity and apparent molar volume of bromates,iodates and sulphates of potassium and sodium in dioxane-water mixtures at different temperatures

The viscosity and apparent molar volume of solutions of KBrO₃, NaBrO₃ KIO₃, NaIO₃, K₂SO₄ and Na₂SO₄ in dioxane (mass fraction: 10, 20 and 30%)-water mixtures at 30, 35, 40 and 45°C have been measured. The ions appear to interact appreciably and the ion-solvent interaction is of the order BrO^?₃ > IO^?₃ > SO^2?₄ and K⁺ > Na⁺.     

Processing and physical properties of native grass-reinforced biocomposites

Big blue stem grass fiber-reinforced high density polyethylene powder biocomposites were fabricated using two separate processing schemes: (1) by compounding biofiber with the thermoplastic powder in an extruder and subsequently injection molding the extrusion pellets and (2) by combining biofiber and the powder thermoplastic powder using a modified sheet molding compounding (SMC) line and subsequently compression molding the sheet material. The physical properties including storage modulus, heat deflection temperature (HDT), notched Izod impact strength, and morphology were evaluated with dynamic mechanical analysis, Izod impact strength measurement, and microscopy observation. It was found that compression-molded specimens achieved similar modulus values to injection molded specimens for grass-reinforced high density polyethylene (HDPE) composites. The stiffness of the compression-molded specimens is related to the consolidation state of the samples, which depends on compression molding conditions such as temperature, pressure, and mold type. Compression-molded specimens exhibited a higher HDT and notched Izod impact strength compared to injection-molded samples. Grass fiber-reinforced cellulose acetate butyrate (CAB) biocomposites made with SMC processing had similar physical properties with grass fiber-reinforced HDPE composites, which indicates that natural fiber-reinforced CAB biocomposites have the potential to replace polyolefin-based composites for automotive applications. POLYM. ENG. SCI. 47:969–976, 2007. © 2007 Society of Plastics Engineers.     

Fusion of smartphone sensor data for classification of daily user activities

Multimedia Tools and Applications - New mobile applications need to estimate user activities by using sensor data provided by smart wearable devices and deliver context-aware solutions to users...     

Microstructure and properties of flame sprayed tungsten carbide coatings

This article reports on feasibility experiments carried out with oxy-acetylene spray system with various oxygen to fuel ratios using two different tungsten carbide powders and powder feeding methods, to evaluate the newly developed fused WC, synthesised by transferred arc thermal plasma method. Transferred arc thermal plasma method is more economical and less energy intensive than the conventional arc method and results in a fused carbide powder with higher hardness. The microstructure and phase composition of powders and coatings were analysed by optical and scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Carbon content of the powders and coatings were determined to study the decarburisation of the material during spraying process. Coatings were also characterised by their hardness and abrasive wear. The effects of metallurgical transformation and phase content are related to wear performance. The results demonstrate that the powders exhibit various degree of phase transformation during the spray process depending on the type of powder, powder feeding and spray parameters. The carbon loss during the spray process in excess of 45% resulted in reduced hardness and wear resistance of the coatings. Coatings with high amount of WC and W₂C along with FeW₃C showed higher wear resistance. Thus, coatings of high wear resistance can be produced using fused tungsten carbide powder with WC and W₂C phases, which can be economically synthesised by thermal plasma transferred arc method.     

Neural Network and Classification Approach in Identifying Customer Behavior in the Banking Sector: A Case Study of an International Bank

The customer relationship focus for banks is in development of main competencies and strategies of building strong profitable customer relationships through considering and managing the customer impression, influence on the culture of the bank, satisfactory treatment, and assessment of valued relationship building. Artificial neural networks (ANNs) are used after data segmentation and classification, where the designed model register records into two class sets, that is, the training and testing sets. ANN predicts new customer behavior from previously observed customer behavior after executing the process of learning from existing data. This article proposes an ANN model, which is developed using a six‐step procedure. The back‐propagation algorithm is used to train the ANN by adjusting its weights to minimize the difference between the current ANN output and the desired output. An evaluation process is conducted to determine whether the ANN has learned how to perform. The training process is halted periodically, and its performance is tested until an acceptable result is obtained. The principles underlying detection software are grounded in classical statistical decision theory.     

Reversible inactivation of purified leukocyte integrin CR3 (CD11b/CD18, alpha m beta 2) by removal of divalent cations from a cryptic site

Integrins exhibit reversible changes in their ability to bind ligands and these changes enable transient cell adhesion. We recently showed that leukocyte integrin CR3 (complement receptor type three, CD11b/CD18, alpha m beta 2) may be purified in a form that is either capable or incapable of binding soluble, monomeric ligand and that "inactive" CR3 may be rendered capable of binding ligand by addition of an anti-CR3 mAb known as KIM-127 (Cai and Wright, JBC. 270: 14358, 1995). Here, we demonstrate that active CR3 may be rendered inactive by treatment of immobilized receptor with EDTA. EDTA-treated CR3 failed to bind ligand even in the presence of mM Ca2+ and Mg2+, suggesting that EDTA-treatment caused a change in the receptor that is not readily reversed. EDTA-treated receptor did, however, bind ligand upon addition of KIM-127 plus Mg2+ with an affinity (17.8 +/- 4.5 nM) similar to untreated, active receptor (12.5 +/- 4.7 nM). EDTA-treated CR3 thus exhibits the properties of inactive CR3, in which the ligand binding site is cryptic but subject to exposure by KIM-127. A candidate for the cryptic ligand binding site is the I-domain, a Mg2+-binding region in the alpha chain of CR3. We found that monomeric C3bi binds directly to recombinant I-domain in a Mg(2+)-dependent fashion with an affinity of 300 +/- 113 nM. These results thus suggest that CR3 may be inactivated by removing tightly bound divalent cation from a cryptic site in CR3.     

Inhibition of neuronal calcium channels by a novel peptide spider toxin, DW13.3

Peptide toxins have proved to be useful agents, both in discriminating between different components of native calcium channel currents and in the molecular isolation and designation of their cloned channel counterparts. Here, we describe the isolation and characterization of the biochemical and physiological properties of a novel 74-amino acid peptide toxin (DW13.3) extracted from the venom of the spider Filistata hibernalis. The subtype specificity of DW13.3 was investigated using calcium channel currents recorded from two separate expression systems and several different cultured mammalian cell preparations. Overall, DW13.3 potently blocked all native calcium channel currents studied, with the exception of T-type currents recorded from GH3 cells. Examination of transiently expressed calcium channels in oocytes showed that DW13.3 had the highest affinity for alpha1A, followed by alpha1B > alpha1C > alpha1E. The affinity of DW13.3 for alpha1B N-type currents varied by 10-fold between expressed channels and native currents. Although block occurred in a similar 1:1 manner for all subtypes, DW13.3 produced a partial block of both alpha1A currents and P-type currents in cerebellar Purkinje cells. Selective occlusion of the P/Q-type channel ligand omega-conotoxin MVIIC (but not omega-agatoxin IVA) from its binding site in Purkinje neurons suggests that DW13.3 binds to a site close to the pore of the channel. The inhibition of different subtypes of calcium channels by DW13.3 reflects a common "macro" binding site present on all calcium channels except T-type.