An electrochemical impedance spectroscopy and scanning electron microscopy study of the influence of positive plate compression on the electrochemical behaviour of lead-acid batteries

This study has developed an electrochemical impedance spectroscopy (EIS) method for the in situ investigation of the influence of positive plate compression on the electrochemical behaviour of lead-acid batteries during charge/discharge cycling. The EIS data for a fully charged and fully discharged battery are internally consistent with the expected kinetics of a battery in the opposite states of charge, and demonstrate that EIS measurements may be recorded with a high level of reproducibility. Furthermore, this study has necessitated the development of a special cell incorporating horizontally orientated battery plates that can be subjected to elevated pressure through the stacking of lead bricks on top of the cell, as well as a physically robust reference electrode system that can withstand the application of pressure. For this purpose, a platinum-wire pseudo-reference electrode has been developed, and has been shown to exhibit sufficient electrode stability over the period of an EIS recording, enabling the measurement of reproducible and meaningful EIS data. Additionally, the influence of positive plate compression on the behaviour of the lead-acid battery has been investigated by using scanning electron microscopy (SEM). Clearly, the experimental data show that plate compression enhances significantly the kinetics and concomitant performance of the lead-acid battery, and this is related to the enhanced reactivity of the active material, as rationalized by using the agglomeration-of-spheres (AOS) model.     

Electrochemical behaviour of copper in neutral aerated chloride solution. I. Steady-state investigation

The electrochemical behaviour of a Cu rotating disc electrode in neutral aerated NaCl solution was investigated in the cathodic and anodic ranges and at the corrosion potential. In the cathodic range, where the reduction of oxygen takes place, reduction peaks allow the identification and quantitative evaluation of insoluble corrosion products (CuCl and Cu₂O). In the anodic range Cu is dissolved, most likely as CuCl ₂ ^– . A new mechanism for the anodic dissolution is proposed after comparing our data with previously published mechanisms. Corrosion currents were found to decrease with time and to be a function of the rotation rate of the electrode. Both the mixed kinetics of the anodic partial reaction and diffusion through a porous layer seem to be relevant in controllingl _corr.     

Multifold behavior of the information transmission by the quantum 3-switch

Quantum Information Processing - A Correction to this paper has been published: https://doi.org/10.1007/s11128-019-2234-5     

Time-domain Analysis of Laboratory Experiments on the Transient Pressure Damping in a Leaky Polymeric Pipe

Water Resources Management - The pressure damping occurring in pressurized pipes with a leak during transients has been examined as a diagnostic tool – the so-called transient damping method...     

Simple approach for the plasma treatment of polymeric membranes and investigation of the aging effect

The modification of the surface characteristics after treatment with plasma in polymeric materials, such as the aging phenomenon, calls the attention of research in the area of nonthermal plasma technology. In this work, a direct treatment with dielectric-barrier discharge plasma was used on the surfaces of ultrafiltration membranes. The measurements of the contact angle with water, attenuated total reflectance accessory, zeta potential, atomic force microscopy and scanning electron microscopy-MEV were performed on the surfaces to verify changes after plasma treatment and to understand the occurrence and timing of the plasma aging effect. In the analysis of the membrane performance, hydraulic permeation and protein retention tests were performed. The results showed an improvement in wettability and hydrophilic properties in the post-treated membranes. The study of reversibility/aging of the post-plasma surface is important for research that deals with the modification of polymeric membranes. Changes in surface morphology, topography and wettability of the membranes were observed up to seven days after treatment, with a tendency to return to the initial characteristics of the membranes.     

Whole-body vibration exposure in sport: four relevant cases

This study investigates the whole-body vibration exposure in kite surfing, alpine skiing, snowboarding and cycling. The vibration exposure was experimentally evaluated following the ISO 2631 guidelines. Results evidenced that the most critical axis is the vertical one. The weighted vibration levels are always larger than 2.5 m/s² and the vibration dose values are larger than 25 m/s^1.75. The exposure limit values of the EU directive are reached after 8–37 min depending on the sport. The vibration magnitude is influenced by the athletes’ speed, by their skill level and sometimes by the equipment. The large vibration values suggest that the practice of sport activities may be a confounding factor in the aetiology of vibration-related diseases.     

Texture Mapping Real‐World Objects with Hydrographics

In the digital world, assigning arbitrary colors to an object is a simple operation thanks to texture mapping. However, in the real world, the same basic function of applying colors onto an object is far from trivial. One can specify colors during the fabrication process using a color 3D printer, but this does not apply to already existing objects. Paint and decals can be used during post‐fabrication, but they are challenging to apply on complex shapes. In this paper, we develop a method to enable texture mapping of physical objects, that is, we allow one to map an arbitrary color image onto a three‐dimensional object. Our approach builds upon hydrographics, a technique to transfer pigments printed on a sheet of polymer onto curved surfaces. We first describe a setup that makes the traditional water transfer printing process more accurate and consistent across prints. We then simulate the transfer process using a specialized parameterization to estimate the mapping between the planar color map and the object surface. We demonstrate that our approach enables the application of detailed color maps onto complex shapes such as 3D models of faces and anatomical casts.     

Mocking Ads through Mobile Web Services

The need for creativity is ubiquitous, and mobile devices connected to Web services can help us. Linguistic creativity is widely used in advertisements to surprise us, to get our attention, and to stick concepts in our memory. However, creativity can also be used as a defense. When we walk in the street, we are overwhelmed by messages that try to get our attention with any persuasive device at hand. As messages get ever more aggressive, often our basic cognitive defenses—trying not to perceive those messages—are not sufficient. One advanced defensive technique is based on transforming the perceived message into something different (for instance, making use of irony or hyperbole) from what was originally meant in the message. In this article, we describe an implemented application for smartphones, which creatively modifies the linguistic expression in a virtual copy of a poster encountered on the street. The mobile system is inspired by the subvertising practice of countercultural art.