Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

Data retention characteristics of sub-100 nm NAND flash memory cells

In contrast to the conventional theories, we have revealed that the most distinguished mechanism in the data retention phenomenon after Fowler-Nordheim (FN) stress in sub-100 nm NAND Flash memory cells is the annihilation of interface states. Interface state generation rate increases rapidly as the channel width of NAND flash cell decreases. Comparison of interface states and stress-induced leakage current (SILC) component during retention mode shows that the annihilation of interface states strongly affects data retention characteristics of the programmed cells.     

Catalytic dehydrogenation of ethylbenzene with carbon dioxide: promotional effect of antimony in supported vanadium–antimony oxide catalyst

Alumina-supported vanadium oxide, VO_x/Al₂O₃, and binary vanadium–antimony oxides, VSbO_x/Al₂O₃, have been tested in the ethylbenzene dehydrogenation with carbon dioxide and characterized by S_BET, X-ray diffraction, X-ray photoelectron spectroscopy, hydrogen temperature-programmed reduction and CO₂ pulse methods. VSbO_x/Al₂O₃ exhibited enhanced catalytic activity and especially on-stream stability compared to VO_x/Al₂O₃ catalyst. Incorporation of antimony into VO_x/Al₂O₃ increased dispersion of active VO_x species, enhanced redox properties of the systems and formed a new mixed vanadium–antimony oxide phase in the most catalytically efficient V_0.43Sb_0.57O_x/Al₂O₃ system.     

A new time-domain discontinuous space-vector PWM technique in overmodulation region

A new discontinuous modulation method based on space-vector control is proposed and analyzed. The proposed technique employs a pulse-dropping method and is designed in the time domain. It features a very wide modulation range while maintaining the required waveform qualities and switching numbers in the overmodulation region. Since the modulation method and modulation index equation are simple, the proposed technique can be easily implemented by software and is applicable to the overmodulation region in ac motor drives. The performance indexes are discussed and experiments have been performed.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

A practical SPICE model based on the physics and characteristics of realistic single-electron transistors

A practical model for a single-electron transistor (SET) was developed based on the physical phenomena in realistic Si SETs, and implemented into a conventional circuit simulator. In the proposed model, the SET current calculated by the analytic model is combined with the parasitic MOSFET characteristics, which have been observed in many recently reported SETs formed on Si nanostructures. The SPICE simulation results were compared with the measured characteristics of the Si SETs. In terms of the bias, temperature, and size dependence of the realistic SET characteristics, an extensive comparison leads to good agreement within a reasonable level of accuracy. This result is noticeable in that a single set of model parameters was used, while considering divergent physical phenomena such as the parasitic MOSFET, the Coulomb oscillation phase shift, and the tunneling resistance modulated by the gate bias. When compared to the measured data, the accuracy of the voltage transfer characteristics of a single-electron inverter obtained from the SPICE simulation was within 15%. This new SPICE model can be applied to estimating the realistic performance of a CMOS/SET hybrid circuit or various SET logic architectures.     

Haemolytic activity of Aeromonas species isolated in Libya

Twenty seven Aeromonas strains (5A. hydrophila, 8A. sobria and 14A. caviae) isolated from children with diarrhoea and 34 Aeromonas strains (9A. hydrophila, 7A. sobria an 18A. caviae) isolated from children without diarrhoea were tested from haemolysin production. The results obtained showed that haemolysin production using human, horse or sheep erythrocytes was significantly associated with A.hydrophila and A sobria but not with A.caviae, regardless of whether these strains were isolated from children with or without diarrhoea. Human or horse rather than sheep erythrocytes are recommended for use in the haemolysin assay.     

A new millimeter-wave step-frequency radar sensor for distancemeasurement

A new compact millimeter-wave distance-measurement sensor prototype has been developed. The sensor is a step-frequency radar implemented using coherent heterodyne technique. It operates in Ka-band (26.5-40 GHz) and is realized using MICs and MMICs. The sensor transmits sinusoidal signals of incremental frequencies and demodulates the received signals into base-band I/Q signals for processing. Experimental results show that the sensor is capable of measuring distance with less than 0.2 inch of absolute error and a low transmitted power of only -20±3 dBm     

Stress analysis of a cantilevered fixed partial denture with normal and reduced bone support

A two-dimensional finite element model was constructed to analyze the simulated mechanical behavior of a cantilevered fixed partial denture. The variations of the models were made by altering the degree of bone support, the number of splinted abutments, and the length of the pontics. High stress concentrations were observed around the connectors of the fixed prosthesis and the tooth closest to the cantilever. Reduced bone support increased the deflection and stress concentrations. There was reduction in displacement and stress concentration when the teeth were splinted together. To improve the prognosis of the fixed partial denture cantilever, the number of abutments should be increased and the number of pontics decreased.