Ultra-wideband (from DC to 110 GHz) CPW to CPS transition

A new ultra-wideband, low-loss and small-size coplanar waveguide (CPW) to coplanar strip (CPS) transition which can be used from DC to 110 GHz is presented. The proposed transition connects CPW with CPS by the reformed air-bridge. Two ground planes of CPW are tied at their ends by a line and the centre of the line is connected to the ground strip of CPS by another line. Owing to the symmetry of the proposed structure, the currents of two ground planes of CPW are combined with the same phase and transferred to the ground strip of CPS. With height of 3 μm, the signal line of CPW passes over two connecting lines and is connected to the signal strip of CPS. For the back-to-back transition structure, insertion loss <1 dB and return loss >15 dB are obtained from 0.5 to 110 GHz     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002     

Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.     

Security of the Cao-Li public key cryptosystem

The author shows that the Cao-Li cryptosystem proposed [1991] is not secure. Its private key can be reconstructed from its public key using elementary means such as LU-decomposition and the Euclidean algorithm     

Long-term effect of inducible silent ischaemia on left ventricular systolic function

A new method of thin section preparation of III-V semiconductors and multilayers for transmission electron microscopy (TEM) is presented that exhibits considerable advantages over conventional methods such as ion beam milling and jet thinning. GaAs thin films and multilayers of GaAs/In chi Ga1-chi As/GaAs are grown over an etch release layer of AlAs on GaAs substrates by molecular beam epitaxy (MBE). Planar TEM sections prepared by selective etching from these samples show improved ability to image film morphology and dislocation arrangements, and the resulting large thin electron transparent areas facilitate dislocation density measurements and detection of spatial variations. Avoidance of radiation effects and wedge shaping, both common to ion milled samples, allows this method to be used to prepare uniform thickness standards of single layer GaAs films for EDS analysis or lattice imaging.     

Study on the propagation of inlet flow distortion in axial compressor using an integral method

 An integral method is investigated and developed in the current work. The effects of the parameters of inlet distortions on the trend of downstream flow feature in compressor are simulated. Other than the drag-to-lift ratio of the blade and the inlet incidence angle, it is found that the distorted inlet velocity is another essential parameter to control the distortion in propagation. Based on this study, a novel critical distortion line and corresponding critical distortion factor are proposed to express the effect of the two essential inlet parameters on the propagation of distortion, namely, the inlet incidence angle and the distorted inlet velocity. From the viewpoint of compressor efficiency, the propagation of inlet flow distortion is further described by a compressor critical performance and its critical characteristic. The results present a useful physical insight to an axial flow compressor behavior and asymptotic behavior of the propagation of inlet distortion, and confirm the active role of compressor in determining the velocity distribution when compressor responds to an inlet flow distortion. Received: 20 December 2001 / Accepted: 21 August 2002 The authors would like to thank HQ RSAF for permission to publish this work, their financial support and encouragement. The first author wants to acknowledge Prof. Frank Marble of California Institute of Technology, for bringing the problem to the author's attention and for his helpful discussion.     

A dynamic frequency grid allocation scheme for the efficient designof equiripple FIR filters

In the design of a digital filter, the frequency response is often optimized to meet a given set of specifications on a dense grid of frequency points. The density of the frequency grid points must be sufficiently high so that the frequency response of the filter does not violate the specifications at frequencies in between the grid points. However, the computational complexity of the design process and the storage requirements of the computer increase with the number of frequency grid points. We propose a novel dynamic: grid point allocation technique for the design of minimax optimum FIR filter. It uses a sparse frequency grid but will produce a design that is the same as one designed on very dense frequency grid points. It requires significantly less computer time and memory resources compared with fixed grid point algorithms     

Analysis and characterization of traveling-wave electrode in electroabsorption modulator for radio-on-fiber application

Comparing with a lumped electroabsorption modulator (EAM), we show the merits of a long EAM with traveling-wave electrode with high radio-frequency (RF) gain that could be used in high-frequency analog application. By terminating the RF output port with the characteristic impedance of 30 /spl Omega/, the device exhibited a large enhancement of 6 dB above 10 GHz in the electrical-to-optical response and a wide fractional bandwidth as estimated from simulation. In addition, an input impedance matching circuit of stub embedded on the device chip was found to be very effective for improving RF characteristics in the narrow band of frequency.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.