Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Simulation of characteristics of double-junction solar cells based on ZnSiP2 heterostructures on silicon substrate

Design and operation modes of double-junction monolithic lattice-matched solar cells based on the ZnSiP₂/Si system of materials have been calculated. The effect of the photoactive region thickness and minority carrier lifetime in ZnSiP₂ layers on the efficiency of conversion of the incident solar light energy into electrical power was determined. It is shown that solar cells based on ZnSiP₂/Si heterostructures can provide efficiencies of 28.8% at AM1.5D, 100 mW/cm², and 33.3% at AM1.5D, 200 W/cm².     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.     

Conveyer-belt accidents in mining and metallurgy

The dynamic interaction between the mechanical and electrical drive parameters when damage suddenly appears in the mechanical part of a conveyer belt is investigated. The possibility of using the change in the motor’s electrical parameters as a diagnostic signal is assessed. A model for investigating the dynamic processes in the system consisting of the grid, the induction motor, and the conveyer belt is proposed. The grid and induction motor are described by a model of fourth-order state space, whose output is the torque at the motor shaft. The moments of inertia and pliability of the links between the elements in the mechanical part of the conveyer belt are determined. By gradually identifying the elements with the minimum moment of inertia and distributing their moments of inertia and pliabilities among the adjacent elements, we obtain a three-mass system simulating the mechanical part of the conveyer belt. This dynamic model is solved by means of Matlab Simulink software. The energy characteristics of the drive are determined in dynamic processes following a mechanical accident.