Simulation-Based Decision Support System for Economical Supply Chain Management of Rebar

The economics of a materials management system is defined by the size of the shipments, the scheduling strategy that allows contractors to handle uncertainty and variability in the supply chain, and the timing of the shipments, which in turn depend on the environment in which the project is taking place. This study presents a simulation-based decision support system to assist contractors in selecting the most economical rebar management system prior to the start of construction by recommending lot sizes (large, small), a scheduling strategy (optimistic, neutral, pessimistic), and buffer sizes (large, medium, small) given the conditions of the project. This model is of benefit to contractors and researchers because it generates the probable cost of inventory of 18 alternative rebar management systems ranging from just in case (JIC) to just in time (JIT) and including different variations in between. It allows contractors to select the alternative with least cost of inventory at the planning stages of a project. The simulation model was tested by using actual data obtained from a trade center project in Istanbul, Turkey. As expected, the test indicated that JIC was the most economical rebar management system in a case study conducted in a developing country, as it generated a savings of 4.8% over JIT.     

Realization of Fully Controllable Negative Inductance with Single Operational Transresistance Amplifier

A grounded negative inductance emulator is proposed with full independent control on both the inductance value and the condition. It uses a single operational transresistance amplifier (OTRA), a capacitor, and five resistors, two of which are for independent control. Experimental results, which confirm the theoretical analysis, are presented.     

Optimization of properties of fly ash aggregates for high-strength lightweight concrete production

The optimization of properties of lightweight fly ash aggregates for suitability in high-strength lightweight fly ash concrete production was investigated using response surface methodology (RSM). Design-Expert software was used to establish the design matrix and to analyze the experimental data. The relationships between the sintering parameters (temperature, binder content and binder type) and experimentally obtained three responses (specific gravity, water absorption and crushing strength) were established. Also, the optimization capabilities in Design-Expert software were used to optimize the sintering process. Historical data design technique under RSM was performed to optimize the input parameter interactions which showed the best conditions for preparation of fly ash pellets. According to the obtained results, the developed models are statistically accurate and can be used for further analysis. The experimental values agreed with the predicted ones, thus indicating suitability of the model employed and the success of RSM in optimizing the sintering conditions.     

Cooperative target pursuit by multiple UAVs in an adversarial environment

This paper presents the development of a cooperation strategy for multiple UAVs to pursue a target moving in an adversarial environment where threat exposure should be minimized, and obstacles and restricted areas should be avoided. A probabilistic approach is used to model the adversarial environment. A cost function is defined to quantify placement of UAVs around the target in formation in terms of threat exposure level and distance to the target. The cost function is used to develop a cooperation strategy for a team of UAVs to follow the target such that the total threat exposure of the team and the average distance to the target throughout the pursuit are minimized according to the weighting coefficients specified. The cooperation strategy has the feature of collision avoidance as well as data-fusion-based estimation of the target trajectory based on noisy measurements. Simulation results have demonstrated that the cooperation reduces the risk of losing the target during the pursuit while avoiding obstacles and restricted areas. Further, the UAVs guided by the cooperation strategy can follow the target closer without increasing the total threat exposure level as compared to cases where the UAVs pursue the target without cooperation.     

Durability of lightweight concretes with lightweight fly ash aggregates

This paper presents the effects of aggregate properties such as strength, porosity, water absorption, bulk density and specific gravity on the strength and durability of lightweight fly ash aggregate concrete (LWAC). The influence of properties of four aggregates (sintered lightweight fly ash aggregates, cold-bonded lightweight fly ash aggregate and normalweight aggregate) on mechanical and durability properties of concrete is discussed. Experimental results revealed that durable high-strength air-entrained lightweight concretes could be produced using sintered or cold-bonded lightweight fly ash aggregates, having comparable performance with the normalweight concretes. The use of lightweight aggregates (LWA) instead of normalweight aggregates in concrete production decreased the strength and stiffness due to the higher porosity and lower strength of the aggregate included in the concrete. However, permeability of sintered fly ash aggregate lightweight concretes was comparable and slightly lower than normalweight concrete whereas permeability of cold-bonded fly ash lightweight concrete was greater than the others. All concretes had a durability factor greater than 85, which met the requirements by showing quite perfect resistance to freeze–thaw.     

A Route Towards Sustainability Through Engineered Polymeric Interfaces

Chemical vapor deposition (CVD) of polymer films represent the marriage of two of the most important technological innovations of the modern age. CVD as a mature technology for growing inorganic thin films is already a workhorse technology of the microfabrication industry and easily scalable from bench to plant. The low cost, mechanical flexibility, and varied functionality offered by polymer thin films make them attractive for both macro and micro scale applications. This review article focuses on two energy and resource efficient CVD polymerization methods, initiated Chemical Vapor Deposition (iCVD) and oxidative Chemical Vapor Deposition (oCVD). These solvent‐free, substrate independent techniques engineer multi‐scale, multi‐functional and conformal polymer thin film surfaces and interfaces for applications that can address the main sustainability challenges faced by the world today.     

The effect of nisin on L. monocytogenes in Turkish fermented sausages (sucuks)

Turkish fermented sausage (sucuk) is a traditional, well-known meat product in Turkey. The aim of this study was to evaluate the effect of different nisin concentrations on Listeria monocytogenes in experimentally contaminated sucuk. Analyses were performed on at 0, 1, 3, 5, 7, 10, 15, 20, 25 and 30days for L. monocytogenes and other microbiological parameters (Total mesophilic aerobic bacteria and lactic acid bacteria) and physico-chemical parameters (pH, a(w) and moisture content).The sucuk dough was contaminated with L. monocytogenes ATCC 7644 at a concentration of 10(6)cfu/g, and the dough was divided into six equal groups. Each group was treated separately with different nisin concentrations (0, 5, 10, 25, 50 and 100μg/g). No L. monocytogenes surviving cells were detected in groups which contained 100μg/g and 50μg/g nisin at day 20 and 25, respectively (p<0.001). In conclusion, the inhibition of L. monocytogenes in sucuk increases with the increasing concentrations of nisin.     

Effects of run‐of‐the‐river hydropower plants on the surface water quality in the Solakli stream watershed,Northeastern Turkey

In recent years, Turkey has turned its attention to alternative energy sources rather than fossil fuels. The Eastern Black Sea Region of Turkey has steep mountains with hilly topography and has large potential in terms of energy production with run‐of‐the‐river hydropower plants (RHPPs). In this study, the effects of two RHPPs on some water quality parameters were examined in the Solakl? stream watershed. This research was conducted over the course of 12 months (January–December 2014). In total, 12 sampling points were selected and various water quality parameters, such as temperature, pH, dissolved oxygen, total suspended solids, electrical conductivity, total dissolved solid, chloride and salinity, were monitered at each point. Statistically, significant changes occured in water quality parameters such as total suspended solids, pH and temperature. In particular, total suspended solids ranged from 10 to 440 mg/L.These results suggest that the RHPP negatively effect water quality and quantity in the main stream in both the operational and constructional phases.