Impact of fertilizer on a small watershed of Lake Biwa: use of sulfur and strontium isotopes in environmental diagnosis

Sulfur and strontium isotopes (delta(34)S and (87)Sr/(86)Sr) were determined in 39 river water samples collected over three different cultivation periods (April, May, and June), and in several materials used for comparison (fertilizers, detergents, soils, irrigation and agricultural waters), to evaluate the impact of fertilizers on a small agricultural watershed of Lake Biwa, in central Japan. delta(34)S values in river water decreased (from +5.8 to -2.0 per thousand) with increasing SO(4) concentrations (3.8 to 93.2 ppm) from upstream to downstream of the watershed. Comparison of river water S isotopes with those of possible source materials indicates that the enrichment of SO(4) can be attributed to the dissolution of two kinds of fertilizers: (1) compound fertilizers commonly used in this area and (2) ammonium sulfate which is applied on a small scale. In contrast, (87)Sr/(86)Sr values of river water decreased with time from April (avg. 0.71163), through May (avg. 0.71139), to June (avg. 0.71127). The tendency of the sample plots on the (87)Sr/(86)Sr vs. 1/Sr diagram suggests a time-dependent increase in the contribution of soil water to the river, which is partly affected by the Sr-bearing fertilizers. It is suggested that a maximum of 25% of dissolved Sr is derived from these fertilizers, while more than 75% of it is of rock origin. Mass balance calculations permitted us to evaluate the proportion of fertilizer contribution in each river. Combined use of S and Sr isotopes together with concentration data could be a new environmental diagnosis technique for rivers and soils in localized watersheds.     

A novel MOSFET with vertical signal‐transfer capability for 3D‐structured CMOS image sensors

We have developed a novel MOSFET that can transfer signals vertically without through‐silicon vias but by using a fully depleted silicon‐on‐insulator (FDSOI) structure with its source region connected to the back electrodes as well as the front ones. A prototype MOSFET fabricated using the backside anisotropic wet etching technique has confirmed that the electrical characteristics measured from the front and the back electrodes are identical. The subthreshold factor S of the prototype was found to be 64.5 mV/decade, suggesting a good switching performance. Since the double‐sided MOSFET has vertical signal‐transfer capability and excellent operating characteristics, it is expected to contribute to developing a More‐than‐Moore type device of three‐dimensional integration such as pixel‐parallel image sensors. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Analysis of nonlinear transient responses of piezoelectric resonators

The electric transient response method is an effective technique to evaluate material constants of piezoelectric ceramics under high-power driving. In this study, we tried to incorporate nonlinear piezoelectric behaviors in the analysis of transient responses. As a base for handling the nonlinear piezoelectric responses, we proposed an assumption that the electric displacement is proportional to the strain without phase lag, which could be described by a real and constant piezoelectric e-coefficient. Piezoelectric constitutive equations including nonlinear responses were proposed to calculate transient responses of a piezoelectric resonator. The envelopes and waveforms of current and vibration velocity in transient responses observed in some piezoelectric ceramics could be fitted with the calculation including nonlinear responses. The procedure for calculation of mechanical quality factor Q(m) for piezoelectric resonators with nonlinear behaviors was also proposed.     

Speech recognition in living rooms: Integrated speech enhancement and recognition system based on spatial,spectral and temporal modeling of sounds

Research on noise robust speech recognition has mainly focused on dealing with relatively stationary noise that may differ from the noise conditions in most living environments. In this paper, we introduce a recognition system that can recognize speech in the presence of multiple rapidly time-varying noise sources as found in a typical family living room. To deal with such severe noise conditions, our recognition system exploits all available information about speech and noise; that is spatial (directional), spectral and temporal information. This is realized with a model-based speech enhancement pre-processor, which consists of two complementary elements, a multi-channel speech–noise separation method that exploits spatial and spectral information, followed by a single channel enhancement algorithm that uses the long-term temporal characteristics of speech obtained from clean speech examples. Moreover, to compensate for any mismatch that may remain between the enhanced speech and the acoustic model, our system employs an adaptation technique that combines conventional maximum likelihood linear regression with the dynamic adaptive compensation of the variance of the Gaussians of the acoustic model. Our proposed system approaches human performance levels by greatly improving the audible quality of speech and substantially improving the keyword recognition accuracy.     

A rechargeable lithium metal battery operating at intermediate temperatures using molten alkali bis(trifluoromethylsulfonyl)amide mixture as an electrolyte

The physicochemical properties of molten alkali bis(trifluoromethylsulfonyl)amide, MTFSI (M = Li, K, Cs), mixture (x_LiTFSI = 0.20, x_KTFSI = 0.10, x_CsTFSI = 0.70) were studied to develop a new rechargeable lithium battery operating at intermediate temperature (100–180 °C). The viscosity and ionic conductivity of this melt at 150 °C are 87.2 cP and 14.2 mS cm⁻¹, respectively. The cyclic voltammetry revealed that the electrochemical window at 150 °C is as wide as 5.0 V, and that the electrochemical deposition/dissolution of lithium metal occurs at the cathode limit. A Li/MTFSI (M = Li, K, Cs)/LiFePO₄ cell showed an excellent cycle performance at a constant current rate of C/10 at 150 °C; 95% of the initial discharge capacity was maintained after 50 cycles. Except for the initial few cycles, the coulombic efficiencies were approximately 100% for all the cycles, indicating the stabilities of the molten MTFSI mixture and all the electrode materials.     

Heat-resisting TCO films for PV cells

We developed new heat-resisting transparent conductive oxide (TCO) films with resistivity of 1.4×10⁻⁴ Ω cm, an optical transmittance of above 80% (at 550 nm) and heat-resisting temperature at above 600 °C. The TCO films consists of fluorine-doped tin oxide films coated on indium–tin oxide films. They were prepared by a spray pyrolysis deposition method on glass substrates. The 100×100 mm² dye-sensitized solar cells (DSCs) were prepared with the TCO films. An energy conversion efficiency of the DSC was improved drastically in comparison to the case with conventional TCO films.     

Mixed powder coating film using thermoplastic polyester and its alkaline resistance

To improve alkaline resistance, a newly mixed powder coating film using thermoplastic polyethylene terephthalate (PET) was investigated. Two kinds of polyvinyl butyral (PVB) and two kinds of polyamide (PA) were chosen as the secondary polymer. The melting temperatures (T _ms) of these materials were lower than that of primary PET polymer so the mixed powder coating was able to form a dual phase film through a fluidized bed coating process. Microscope and Fourier transform infrared spectroscopy (FTIR) observations revealed that the dual phase structure was indeed successfully formed and there was a secondary layer over the entire surface area of the film. This mixed powder coating film significantly enhanced the alkaline resistance to an environment filled with NaOH solution at 40°C in which a secondary material would be effective in protecting the film. With regard to both alkaline resistance and film formability, PET/PVB was superior to the PET/PA mixture.     

A behavioral model for optically powered OCT endoscope with a micro electrostatic vertical‐comb optical scanner

This paper presents a novel device architecture for optically actuated microelectromechanical systems (MEMS) endoscopes for optical coherence tomography (OCT) measurement. A 10‐mW infrared light beam at a wavelength of 1.5 µm is transferred through the single‐mode fiber to provide a scanning MEMS mirror with the drive voltage (maximum 11 V) by exciting a photovoltaic cell, while also providing with a secondary light beam at a wavelength of 1.3 µm for the OCT measurement. An electrostatic vertical comb‐drive optical scanner (1.5 mm × 2.0 mm × 0.5 mm) has been developed by using the deep reactive ion etching (DRIE) of a silicon‐on‐insulator (SOI) wafer. The design of the scanner module is discussed, along with the experimental results of electrostatic operation. An equivalent circuit model for the optical scanner is developed to explain the behavior of the optically powered actuation mechanism, including the hysteresis loop in the frequency response and the voltage dependence of oscillating angle (mechanical peak ±3.2°/7 V around the resonance frequency of 250 Hz). OCT measurement of a tissue is demonstrated to reconstruct the cross‐sectional image of a fingerprint at a resolution of lateral 40 µm × vertical 8 µm and penetration depth of 2.5 mm. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Steam gasification of coal cokes in an internally circulating fluidized bed of thermal storage material for solar thermochemical processes

A laboratory-scale prototype windowed internally circulating fluidized-bed reactor made of quartz sand and coal coke particles was investigated for steam gasification using concentrated Xe-light radiation as the energy source. The quartz sand was used as a chemically inert bed material for the fluidized bed, while the coal coke particles functioned as the reacting particles for the endothermic gasification reaction. The advantages of using quartz sand as the bed material for the directly irradiated gasification reactor are as follows: (1) The bed height is maintained at a constant level during the gasification. (2) The quartz sand functions as a thermal transfer/storage medium inside the reactor. The gasification performances such as the production rates of CO, H₂, and CO₂; carbon conversion; and light-to-chemical energy conversion were evaluated for the fluidized-bed reactor with a thermal transfer/storage medium (quartz sand). The effects of using the bed material (quartz sand) on the gasification performance are described in this paper.