Adhesive element modelling and weighted static shape control of composite plates with piezoelectric actuator patches

A novel finite element model is presented for static and dynamic analysis of composite plates integrated with a laminated piezoelectric layer, a host laminated composite plate and an adhesive layer between them. A new adhesive element is developed which includes both peel and shear effects in the adhesive layer based on first‐order shear deformation plate theory. The thin adhesive layer between the piezoelectric layer and the host plate is modelled by assuming that it carries constant shear and peel strains throughout its thickness. In addition, a weighted static shape control scheme for finding the optimal voltage distribution for static shape control is given. By selecting different weighting matrices, a variety of items such as displacements, slopes, curvatures, strains and even generalized forces, can be included in finding the optimal actuating voltage for static shape control. The present model is validated by comparing with those results available in the literature. The numerical results show that the weighted linear least method can give a satisfactory voltage distribution to best match the desired shape. Copyright © 2004 John Wiley & Sons, Ltd.     

螺栓角钢钢节点的三维非线性有限元分析

对螺栓角钢钢节点半刚性连接采用非线性有限元分析方法 ,对连接中的主要构件的顶部、底部、腹板角钢、高强螺栓、梁翼缘、柱翼缘和柱翼缘加劲肋进行三维非线性有限元精细模拟 ,针对有无柱加劲肋、有无腹板角钢等几种连接的情况进行比较分析 ,探讨了螺栓角钢半刚性连接的受力性能。     

Two-dimensional symmetric multimode interferences in silicon square waveguides

Symmetric interference in two-dimensional multimode silicon waveguides is experimentally investigated. For a 100/spl times/100 /spl mu/m/sup 2/ cross section, 2700-/spl mu/m-long waveguide fabricated on silicon-on-insulator substrate, an 8/spl times/8 matrix of replicated images with high contrast ratio is demonstrated for 1530-1570 nm wavelength range. Symmetric interference results in reduced device length, and the actual device length is consistent with the theoretical expectation. The device also exhibits stable imaging in terms of good loss uniformity, and low wavelength and polarization dependencies among the replicated images.     

IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

便携式全站仪在钻采井架钢结构安装中的应用

文章介绍了一种由便携机和全站仪组成的便携式全站仪 ,阐述了该全站仪在钻采井架钢结构施工安装过程中的测量工作 ,对测点产生的误差采用伪逆自由网平差方法进行处理 ,控制点的精度可达到± 5mm ,该全站仪具有快速、灵活、准确的特点 ,不仅提高了生产效率 ,而且达到了对资料的计算机化管理。     

Verification of submodeling technique in thermomechanical reliability assessment of flip-chip package assembly

In this paper we verified the submodeling technique applied in the thermomechanical reliability assessment of a flip-chip BGA under accelerated thermal cycling test conditions. Since the steady-state creep model was implemented for the solder bump to better represent its realistic mechanical behavior, submodeling procedures developed specifically for path-dependent thermomechanical problems were considered. A detailed global model for the flip-chip BGA was built up to verify submodeling solutions. This model also served as a benchmark to examine solution discrepancies caused by different simplifications of the global model.     

SDS/正戊醇/水体系的液晶研究

在 2 5℃测定了十二烷基硫酸钠 (SDS) /正戊醇 /水三元体系的相平衡 ,确定了液晶区域的边界范围。在液晶区域内选取一系列样品点 ,用差示扫描量热法 (DSC)和2 HNMR与液晶照片对照 ,研究了该体系的液晶结构特点。结果表明 :在恒定温度下 ,该体系存在着两个液晶区域 ,并且随含水量的增加 ,液晶结构发生变化。当组成固定时 ,体系的液晶相结构随温度升高也发生变化     

超分子主体化合物在分析化学中的应用研究进展

综述了近年来超分子主体化合物在分析化学领域的应用研究与进展。分别以冠醚、环糊精、杯芳烃、卟啉4类超分子为主体功能化合物的研究进行了详细的评述，并对这几类主体化合物在分析化学中的应用研究进行了展望。     

中间馏分油型加氢裂化催化剂用沸石的研究

通过水热处理法制备了3个不同脱铝深度的改性Y沸石，再经浸渍法制成中间馏分油型加氢裂化催化剂，在200mL小型加氢裂化装置上进行了催化性能评价。试验结果表明，除了沸石的酸性外，其孔结构和比表面积对催化剂的活性、中间馏分油选择性和液体收率都有很大的影响，为最大幅度提高催化剂的中间馏分油选择性并保持较好活性，要求沸石具有较低的酸量、较高的比表面积和较多的二次孔及适量的L酸量。     

新型超微晶软磁合金FePCCuMoSi微观结构缺陷的正电子湮没研究

用正电子湮没方法研究了新型超微晶软磁合金的微观结构缺陷，样品选用的是在不同温度下退火的Ｆｅ８１Ｐ１２Ｃ３Ｃｕ１Ｍｏ０．５Ｓｉ２．５合金，结果表明，合金的微观结构构陷大小，密度随退火温度有规律地变化，这种现象可能与非晶的晶化过程有关。