On the comparison between OFDM and single carrier modulation with aDFE using a frequency-domain feedforward filter

Most comparisons between single carrier and multicarrier modulations assume frequency-domain linear equalization of the channel. We propose a new frequency-domain decision feedback equalizer (FD-DFE) for single carrier modulation, which makes use of a data block transmission format similar to that of the orthogonal frequency-division multiplexing with cyclic prefix (OFDM). The scheme is a nonadaptive DFE where the feedforward part is implemented in the frequency domain, while feedback signal is generated by time-domain filtering. Through simulations in a HIPERLAN-2 scenario, we show that FD-DFE yields a capacity very close to that of OFDM. This result is also confirmed by analytical derivations for a particular case. Furthermore, when no channel loading is considered, FD-DFE performs closely to OFDM for the same averaged frame error rate in a coded transmission. Design methods of the FD-DFE are investigated and a reduced complexity technique is developed, with the result that FD-DFE and OFDM have a similar computational complexity in signal processing     

Adaptive antenna system design for multi-element combining with transient interrupted channels

This paper presents an analysis and design procedure for a buoyant cable array antenna used for satellite communications. The towed multi-element array is susceptible to washovers and fluctuations due to the ocean wave interaction with the floating hose where the elements are housed. A model of system performance for coherent multi-element combining is presented based on the dropouts and fades of the individual elements. The array design, including the number and spacing of elements, is shown to be highly dependent on the individual element exposure characteristics and the degree of correlation of the fades between channels. The joint statistics of the array are analyzed using a binary conditional element exposure model and a first-order Markov interelement correlation model. Using this analysis, a family of array designs meeting the communications requirements is produced.     

Improvement in the DOA estimation of broadband signals usingpartially IIR beamformers

An ideal broadband beamformer requires an increased number of taps for each filter, which in turn increases the complexity of the design. It is shown that for angles near the broadside of the antenna the beamforming is more accurate compared to the angles near the endfire, and it is advantageous to use recursive filters combined with a computed number of zeros for angles near the endfire. The proposed method is used for estimating the arrival angle of the incoming signals and displays uniform accuracy for all angles     

InP D-HBT ICs for 40-Gb/s and higher bitrate lightwave transceivers

The combination of device speed (f/sub T/, f/sub max/ > 150 GHz) and breakdown voltage (V/sub bceo/ > 8 V) makes the double heterojunction bipolar InP-based transistor (D-HBT) an attractive technology to implement the most demanding analog functions of 40-Gb/s transceivers. This is illustrated by the performance of a number of analog circuits realized in an InP D-HBT technology with an 1.2- or 1.6-/spl mu/m-wide emitter finger: a low phase noise push-push voltage-controlled oscillator with -7-dBm output power at 146 GHz, a 40-GHz bandwidth and low-jitter 40-Gb/s limiting amplifier, a lumped 40-Gb/s limiting driver amplifier with 4.5-V/sub pp/ differential output swing, a distributed 40-Gb/s driver amplifier with 6-V/sub pp/ differential output swing, and a number of distributed preamplifiers with up to 1.3-THz gain-bandwidth product.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

Quantisation noise control in perceptual audio coding using low selectivity filter banks

The problem of computing, in a subband audio coder, the maximum quantisation noise power that can be injected in each band to ensure transparent coding when low selectivity filter banks are used, is addressed. A low complexity strategy, taking into account the frequency responses of the synthesis filter bank, is proposed for achieving an overall distortion due to quantisation noise always below the masking threshold (provided by a psycho-acoustic model) for any length prototype filters.     

Magnetic effects of direct ion implantation of Mn and Fe into p-GaN

In p-GaN implanted with Mn (3×10¹⁶ cm⁻² at 250 keV), the material after annealing shows ferromagnetic properties below 250 K. Cross-sectional transmission electron microscopy (TEM) revealed the presence of platelet structures with hexagonal symmetry. These regions are most likely Ga_xMn_1−xN, which produce the ferromagnetic contribution to the magnetization. In p-GaN implanted with Fe, the material after annealing showed ferromagnetic properties at temperatures that were dependent on the Fe dose, but were below 200 K in all cases. In these samples, TEM and diffraction analysis did not reveal any secondary phase formation. The results for the Fe implantation are similar to those reported for Fe doping during epitaxial growth of GaN.     

The measurement of solar array discharges in a simulated spaceenvironment

A spacecraft in a plasma builds up charge on all the dielectric surfaces and interfaces. Once the net charge exceeds the dielectric breakdown of the material, a discharge occurs. One of the more susceptible pieces of equipment is the antenna/receiver system. The radiated E-field may be strong enough to create an ambiguous signal which may be misinterpreted by the system electronics and cause a system malfunction. A technique is developed to monitor the radiated E-field of materials discharging in an electron environment, using vacuum chambers for measuring the material discharges which are made of highly reflective materials. These chambers affect the radiated E-field due to multiple reflections from the walls. The technique developed defines a method for correcting the effects caused by the measurement facilities. The methodology is: monitor the radiated E-field with a broadband dipole antenna, and digitize the radiated signal as a function of time. Determine the frequency response of the radiated E-field using an FFT algorithm. Measure the transmission and reflection characteristics of the two-port network inside the measurement chamber, and determine the impedance network from the measured E-parameters across the frequency band of interest. Transform the measured E-field frequency response through the impedance network to obtain the frequency response of the actual radiated discharge current. Find the inverse FFT of this response to obtain the actual radiated discharge current response. This technique aids in the prediction of the E-field coupling into receive antennas on-board actual satellites