Effect of injection timing on the exhaust emissions of a diesel engine using diesel–methanol blends

Environmental concerns and limited resource of petroleum fuels have caused interests in the development of alternative fuels for internal combustion (IC) engines. For diesel engines, alcohols are receiving increasing attention because they are oxygenated and renewable fuels. Therefore, in this study, the effect of injection timing on the exhaust emissions of a single cylinder, naturally aspirated, four-stroke, direct injection diesel engine has been experimentally investigated by using methanol-blended diesel fuel from 0% to 15% with an increment of 5%. The tests were conducted for three different injection timings (15°, 20° and 25 °CA BTDC) at four different engine loads (5 Nm, 10 Nm, 15 Nm, 20 Nm) at 2200 rpm. The experimental test results showed that Bsfc, NO_x and CO₂ emissions increased as BTE, smoke opacity, CO and UHC emissions decreased with increasing amount of methanol in the fuel mixture. When compared the results to those of original injection timing, NO_x and CO₂ emissions decreased, smoke opacity, UHC and CO emissions increased for the retarded injection timing (15 °CA BTDC). On the other hand, with the advanced injection timing (25 °CA BTDC), decreasing smoke opacity, UHC and CO emissions diminished, and NO_x and CO₂ emissions boosted at all test conditions. In terms of Bsfc and BTE, retarded and advanced injection timings gave negative results for all fuel blends in all engine loads.     

Process control at the sealing line during sheet metal hydroforming

Sheet metal hydroforming is a deep drawing process that uses a pressure medium for load transmission. The process is mainly influenced by the control of the blank holder force and the fluid pressure. This report describes investigations of a newly developed process-control system. Process variables can be controlled by the sealing state of the tool. The detection is performed by a CCD-camera system that allows the continuous recording of occurring leakages. Different control strategies can be used to control the multiple process parameters. This paper describes the performance and the limits of the aforementioned technology.     

Termite Resistance of MDF Panels Treated with Various Boron Compounds

In this study, the effects of various boron compounds on the termite resistance of MDF panels were evaluated. Either borax (BX), boric acid (BA), zinc borate (ZB), or sodium perborate tetrahydrate (SPT) were added to urea-formaldehyde (UF) resin at target contents of 1%, 1.5%, 2% and 2.5% based on dry fiber weight. The panels were then manufactured using 12% urea-formaldehyde resin and 1% NH₄Cl. MDF samples from the panels were tested against the subterranean termites, Coptotermes formosanus Shiraki. Laboratory termite resistance tests showed that all samples containing boron compounds had greater resistance against termite attack compared to untreated MDF samples. At the second and third weeks of exposure, nearly 100% termite mortalities were recorded in all boron compound treated samples. The highest termite mortalities were determined in the samples with either BA or BX. Also, it was found that SPT showed notable performance on the termite mortality. As chemical loadings increased, termite mortalities increased, and at the same time the weight losses of the samples decreased.     

Parasitic compensation in CCI-based circuits for reduced power consumption

In this paper, the compensation advantage of the first-generation current conveyor (CCI) over the second-generation current conveyor (CCII) in tunable circuits is shown. For this purpose, a new floating frequency dependent negative resistor (FDNR) simulator using three CCIs is presented and employed in a third-order high-pass filter. The compensation feature of the CCI is shown for the proposed high-pass filter. As a second example, the presented compensation method is tested in a second-order band-pass filter constructed with two CCIs. Applying the proposed compensation technique, the CCI-based circuits can operate in lower biasing currents, which result in lower power consumption.     

Ge-Si-O phase separation and Ge nanocrystal growth in Ge:SiO(x)/SiO(2) multilayers--a new dc magnetron approach

Ge:SiO(x)/SiO(2) multilayers are fabricated using a new reactive dc magnetron sputtering approach. The influence of the multilayer stoichiometry on the ternary Ge-Si-O phase separation and the subsequent size-controlled Ge nanocrystal formation is explored by means of x-ray absorption spectroscopy, x-ray diffraction, electron microscopy and Raman spectroscopy. The ternary system Ge-Si-O reveals complete Ge-O phase separation at 400?°C which does not differ significantly to the binary Ge-O system. Ge nanocrystals of < 5?nm size are generated after subsequent annealing below 700?°C. It is shown that Ge oxides contained in the as-deposited multilayers are reduced by a surrounding unsaturated silica matrix. A stoichiometric regime was found where almost no GeO(2) is present after annealing. Thus, the Ge nanocrystals become completely embedded in a stoichiometric silica matrix favouring the use for photovoltaic applications.     

A comparative study on structural,morphological and photocatalytic properties of anodically grown ZnO nanowires under varying parameters

Journal of Materials Science: Materials in Electronics - In this study, zinc oxide (ZnO) nanowires (NWs) were successfully produced on Zn plates through electrochemical anodization in potassium...     

Styrenation of triglyceride oils by macromonomer technique

A novel macromer technique is described for the styrenation of triglyceride oils. Triglyceride oil-based macromers were prepared via successive transesterification and condensation reactions. The macromers were styrenated at 100°C using benzoyl peroxide as an initiator. The styrenation led to improved film properties with semidrying oils. Homopolymerization of the macromonomers failed due to the stearic hindrance of the bulky oil moieties. The results obtained were also evaluated by considering the degree of unsaturation. Chemical Engineering Dept., 80628 Maslak — ISTANBUL Tel.: +90 212 285 6835 or 6836 Fax.: +90 212 285 2925.     

Effect of tap spacing on observed differential pressure fluctuations in a pneumatic transport line

The standard deviation of differential pressure fluctuations between pressure taps in a 31.7 mm i.d. vertical downer was found to be proportional to the square root of the distance between the taps when measured under otherwise constant conditions. This finding confirms the prediction of a theoretical model based on the Central Limit Theorem of sampling statistics. Although the paper only presents experimental confirmation for downward flow, the theoretical model should be valid for flows in all orientations. Except at very low solids flows, the pressure gradient was found to be positive in the flow direction, indicating that rise in pressure due to static pressure more than compensated for frictional pressure losses.