Microstructure and flow behaviour during backward extrusion of semi-solid 7075 aluminium alloy

The microstructure and flow behaviour during thixo backward extrusion of 7075 aluminium alloy were investigated. Reheating the steel die and the aluminium billet placed into the die at the same time using an induction furnace provides rapidly a very homogeneous microstructure suitable for thixoforming. During thixoextrusion, despite the high solid fraction, the solid globules are weakly connected and slide over each other without any plastic deformation. The flow remains quasi homogeneous resulting in homogeneous induced microstructure of the component.     

Structural design of carbon/epoxy bio‐inspired wind turbine blade using fluid/structure simulation

The purpose of this paper is to present the structural design procedure of a low‐speed, horizontal axis, bio‐inspired wind turbine blade made of carbon/epoxy. The methodology initiates with the mechanical characterization of the carbon fiber composite material. An aerodynamic simulation using Computational Fluid Dynamics (CFD) method is performed in order to obtain the pressure distribution profile of the blade. This result is coupled with a Finite Element Analysis (FEA) to carry out an iterative design process through a Fluid‐Structure Interaction (FSI) simulation. Different stacking sequences of laminates are evaluated to find a configuration which allows balance between aerodynamic and dynamic inertial loads, ensuring an almost undeformed geometry during wind turbine's operation. The final structural design of the blade consists in six regions with different laminates. These are balanced and symmetric with distinct thickness characteristics and stacking sequences, which vary in three different orientations: 0^°, ± 45^° and 90^°, achieving a minimum deflection at the tip close to 3.11 cm, and a total weight of 3.6 kg of a 1.8 m radius blade, even with the restrictions imposed by the non‐conventional geometry. Copyright © 2016 John Wiley & Sons, Ltd.     

Molds and Resists Studies for Nanoimprint Lithography of Electrodes in Low-Voltage Polymer Thin-Film Transistors

A low-cost patterning of electrodes was investigated looking forward to replacing conventional photolithography for the processing of low-operating voltage polymeric thin-film transistors. Hard silicon, etched by sulfur hexafluoride and oxygen gas mixture, and flexible polydimethylsiloxane imprinting molds were studied through atomic force microscopy (AFM) and field emission gun scanning electron microscopy. The higher the concentration of oxygen in reactive ion etching, the lower the etch rate, sidewall angle, and surface roughness. A concentration around 30 % at 100 mTorr, 65 W and 70 sccm was demonstrated as adequate for submicrometric channels, presenting a reduced etch rate of 176 nm/min. Imprinting with positive photoresist AZ1518 was compared to negative SU-8 2002 by optical microscopy and AFM. Conformal results were obtained only with the last resist by hot embossing at 120 °C and 1 kgf/cm² for 2 min, followed by a 10 min post-baking at 100 °C. The patterning procedure was applied to define gold source and drain electrodes on oxide-covered substrates to produce bottom-gate bottom-contact transistors. Poly(3-hexylthiophene) (P3HT) devices were processed on high-κ titanium oxynitride (TiO _x N _y ) deposited by radiofrequency magnetron sputtering over indium tin oxide-covered glass to achieve low-voltage operation. Hole mobility on micrometric imprinted channels may approach amorphous silicon (～0.01 cm²/V s) and, since these devices operated at less than 5 V, they are not only suitable for electronic applications but also as sensors in aqueous media.     

The dorsolateral pre‑frontal cortex bi‑polar error‑related potential in a locked‑in patient implanted with a daily use brain–computer interface

While brain computer interfaces (BCIs) offer the potential of allowing those suffering from loss of muscle control to once again fully engage with their environment by bypassing the affected motor system and decoding user intentions directly from brain activity, they are prone to errors. One possible avenue for BCI performance improvement is to detect when the BCI user perceives the BCI to have made an unintended action and thus take corrective actions. Error-related potentials (ErrPs) are neural correlates of error awareness and as such can provide an indication of when a BCI system is not performing according to the user’s intentions. Here, we investigate the brain signals of an implanted BCI user suffering from locked-in syndrome (LIS) due to late-stage ALS that prevents her from being able to speak or move but not from using her BCI at home on a daily basis to communicate, for the presence of error-related signals. We first establish the presence of an ErrP originating from the dorsolateral pre-frontal cortex (dLPFC) in response to errors made during a discrete feedback task that mimics the click-based spelling software she uses to communicate. Then, we show that this ErrP can also be elicited by cursor movement errors in a continuous BCI cursor control task. This work represents a first step toward detecting ErrPs during the daily home use of a communications BCI.     

野性的呼唤 巴西HAIGHT店铺

<正>当一座建筑呈现在室内设计师的眼前时,它往往已经粉刷了墙体,隐藏了所有管线,你已经无法认识它最本原的面貌,设计师无非是在此基础上不断地叠加更多的装饰,让它越来越华丽,遮盖一切最初的痕迹,抹去所有最原始的结构。有没有一位设计师的工作是主动剥去建筑的外衣,让它更加暴露更加原始?总部位于巴西的MNMA Studio就用这样的逆向思维为时尚品牌Haight设计了一个80 m~2零售店,