38. R&D on hydrogen production by high-temperature electrolysis of steam

One of the objectives of the high-temperature engineering test reactor (HTTR) is to demonstrate the effectiveness of high-temperature nuclear heat utilization, which aims to extend the application of nuclear heat to non-electric fields, especially to hydrogen production. As part of the development of the hydrogen production processes, laboratory-scale experiments of a high-temperature electrolysis of steam (HTES) had been carried out with a practical electrolysis tube with 12 solid-oxide cells connected in series. Using this electrolysis tube, hydrogen was produced at the maximum density of 44 N cm³/cm² h at a electrolysis temperature of 950 °C. Thereafter, to improve hydrogen production performance, a self-supporting planar electrolysis cell with a practical size (80 mm × 80 mm of electrolysis area) was fabricated. In the preliminary electrolysis experiment carried out at 850 °C, the planar cell produced hydrogen at the maximum density of 38 N cm³/cm² h, and the energy efficiency was almost as high as that obtained with the electrolysis tube at 950 °C. However, both electrolysis tubes and planar cells did not keep their integrity in one thermal cycle. Durability of the solid-oxide cell against the thermal cycle is one of the key issues of HTES.     

Bending Behavior of Steel Pipe Girders Filled with Ultralight Mortar

Bending behavior of steel pipes filled with ultralight mortar was studied by bending tests using a steel pipe, steel pipes filled with ultralight mortar, and steel pipes filled with light aggregate concrete and normal concrete. The steel pipe model filled with normal concrete had 1.8 times higher bending strength than the steel pipe model. The bending behavior of the steel pipe filled model with ultralight mortar was not improved when the compressive strength of the ultralight mortar was less than 1 MPa. However, ductility was much improved when the compressive strength was over 5 MPa, and the ultimate steel strain was more than double of the steel pipe model. The strains of steel and concrete in all the models were proportional to the distance from the neutral axis until the steel plate yielded. A simple analytical method was proposed to calculate the bending moments of the ultralight mortar filled steel pipes. The calculated values agreed very well with the test results.     

Remote sensing of vegetation and land-cover change in Arctic Tundra Ecosystems

The objective of this paper is to review research conducted over the past decade on the application of multi-temporal remote sensing for monitoring changes of Arctic tundra lands. Emphasis is placed on results from the National Science Foundation Land-Air-Ice Interactions (LAII) program and on optical remote sensing techniques. Case studies demonstrate that ground-level sensors on stationary or moving track platforms and wide-swath imaging sensors on polar orbiting satellites are particularly useful for capturing optical remote sensing data at sufficient frequency to study tundra vegetation dynamics and changes for the cloud prone Arctic. Less frequent imaging with high spatial resolution instruments on aircraft and lower orbiting satellites enable more detailed analyses of land cover change and calibration/validation of coarser resolution observations.The strongest signals of ecosystem change detected thus far appear to correspond to expansion of tundra shrubs and changes in the amount and extent of thaw lakes and ponds. Changes in shrub cover and extent have been documented by modern repeat imaging that matches archived historical aerial photography. NOAA Advanced Very High Resolution Radiometer (AVHRR) time series provide a 20-year record for determining changes in greenness that relates to photosynthetic activity, net primary production, and growing season length. The strong contrast between land materials and surface waters enables changes in lake and pond extent to be readily measured and monitored.     

Deuterium trapping by irradiation damage in tungsten induced by different displacement processes

The deuterium trapping behaviors in tungsten damaged by light ions with lower energy (10 keV C⁺ and 3 keV He⁺) or a heavy ion with higher energy (2.8 MeV Fe²⁺) were compared by means of TDS to understand the effects of cascade collisions on deuterium retention in tungsten. By light ion irradiation, most of deuterium was trapped by vacancies, whose retention was almost saturated at the damage level of 0.2 dpa. For the heavy ion irradiation, the deuterium trapping by voids was found, indicating that cascade collisions by the heavy ion irradiation would create the voids in tungsten. Most of deuterium trapped by the voids was desorbed in higher temperature region compared to that trapped by vacancies. It was also found that deuterium could accumulate in the voids, resulting in the formation of blisters in tungsten.     

Production of High Fructose Syrup by Glucose Isomerase Immobilized on Phenol-Formaldehyde Resin

An immobilized glucose isomerase which is active and stable in concentrated glucose solution has been developed. The enzyme has been immobilized to Duolite A7 resin simply by adsorption. Industrial application of this immobilized enzyme for the continuous production of high fructose syrup is quite promising because the immobilized enzyme having enough mechanical strength against the pressure of column flow, is active over broad ranges of both temperature and pH and is less dependent on Mg and Coions. Long-run continuous experiments in column system have been carried out, isomerizing 45% of glucose with flow rate of SV 1 at 60°C. A gradual decrease of activity was observed after 25 d operation and the half-life was calculated to be 36 d. One liter of the immobilized enzyme in column isomerized 288 kg of glucose in a month. The values of kinetic parameters of the immobilized enzyme in column operation varied with flow rates and approached to those of the native enzyme when they were assayed at the flow rate approaching to SV 0.     

Development of a simple method for fabrication of transparent conductive films with high mechanical strength

We have developed a simple method of fabricating transparent conductive films with a high mechanical strength on glass and indium tin oxide substrates. It does not require a large excess of organic solvents and polymerization catalysts and can yield smooth films by spin-coating of a mixture of a commercially available aqueous dispersion of poly(3,4-ethylenedioxythiophene)-poly(4-styrene sulfonate) and a neat liquid of tetraethyl orthosilicate. Preparation conditions such as feed ratio, kinds of additives, and annealing temperature and time were optimized to give highly conductive, transparent and mechanically strong films.     

Fabrication of alumina films with laminated structures by ac anodization

Anodization techniques by alternating current (ac) are introduced in this review. By using ac anodization, laminated alumina films are fabricated. Different types of alumina films consisting of 50–200 nm layers were obtained by varying both the ac power supply and the electrolyte. The total film thickness increased with an increase in the total charge transferred. The thickness of the individual layers increased with the ac voltage; however, the anodization time had little effect on the film thickness. The laminated alumina films resembled the nacre structure of shells, and the different morphologies exhibited by bivalves and spiral shells could be replicated by controlling the rate of increase of the applied potentials.     

Heavy metal precipitation by polycation-polyanion complex of PEI and its phosphonomethylated derivative

The removal of various heavy metal ions such as Cu2+, Co2+, Zn2+, Ni2+ and Pb2+ from aqueous solutions by precipitation with polyelectrolyte complex of PPEI and PEI was conducted. Heavy metal binding with PPEI was initially allowed to occur and then upon equilibration, PEI was added to initiate precipitation of the polyelectrolyte complex together with the heavy metal ion. The PPEI-PEI system was found effective for heavy metal scavenging purposes even in the presence of high concentrations of non-transition metal ions like Na+. Heavy metal concentration may be reduced beyond emission standards for industrial wastewaters. The PPEI-PEI polyelectrolyte complex was found to be more effective than traditional precipitation methods for the treatment of a representative electroless Ni plating waste solution.     

Dimethyl Fumarate Induces Apoptosis via Inhibition of NF-κB and Enhances the Effect of Paclitaxel and Adriamycin in Human TNBC Cells

Triple-negative breast cancer (TNBC) has the poorest prognosis of all breast cancer subtypes. Recently, the activation of NF-κB, which is involved in the growth and survival of malignant tumors, has been demonstrated in TNBC, suggesting that NF-κB may serve as a new therapeutic target. In the present study, we examined whether dimethyl fumarate (DMF), an NF-κB inhibitor, induces apoptosis in TNBC cells and enhances the apoptosis-inducing effect of paclitaxel and adriamycin. Cell survival was analyzed by the trypan blue assay and apoptosis assay. Protein detection was examined by immunoblotting. The activation of NF-κB p65 was correlated with poor prognosis in patients with TNBC. DMF induced apoptosis in MDA-MB-231 and BT-549 cells at concentrations that were non-cytotoxic to the normal mammary cell line MCF-10A. Furthermore, DMF inhibited NF-κB nuclear translocation and Survivin, XIAP, Bcl-xL, and Bcl-2 expression in MDA-MB-231 and BT-549 cells. Moreover, DMF enhanced the apoptosis-inducing effect of paclitaxel and adriamycin in MDA-MB-231 cells. These findings suggest that DMF may be an effective therapeutic agent for the treatment of TNBC, in which NF-κB is constitutively active. DMF may also be useful as an adjuvant therapy to conventional anticancer drugs.     

Self-assembly of three dimensional micro mechanisms using thermal shrinkage of polyimide

This paper describes three-dimensional microstructures fabricated using a simple self-assembly process involving the thermal shrinkage of polyimide. The proposed method enables hinged structures to be automatically rotated out of the wafer plane and to remain bent without the need to use any interlocking mechanisms. The hinged structures were fabricated using surface micromachining techniques involving heating in a furnace. An increase in the bending angle due to the shrinkage of polyimide was observed with increasing heating temperature, heating time, and length of the polyimide hinge. Of these three parameters, the heating time was found to be the most suitable for precise control of the bending angle. Furthermore, microcubes were fabricated by this method and the self-assembly process was successfully visualized using a CCD camera.