Rotary scanning wireless temperature measurement method for hyperthermia using ferromagnetic implants

Recently, the use of a ferromagnetic material in a soft‐heating method has garnered much attention as a novel method for cancer treatment. By concurrently using this material as a thermal probe, we are currently developing a minimally invasive heating and wireless temperature measurement system. To make the approach feasible in a clinical setting, it is vital to overcome the key challenge of heating the local tumor at a constant temperature. In previous conventional approaches, it was necessary to switch the induction‐heating power supply on/off after the target tumor temperature was reached. However, it cannot determine the temperature of the material during the power‐off period. Therefore, we changed this approach and found that by adjusting the distance between the heating coil and the material while maintaining a constant current flow in heating coil, the drift problem, which happened just after power is supplied during the on/off operation, did not occur any longer. Accordingly, it was not required to use multiple sensors to reduce the drift, thereby minimizing the cost. This study verifies the validity of our wireless thermometry approach while performing rotary scanning and proposes a technique for determining achievement of the target temperature. This knowledge complements other approaches for cancer treatment utilizing hyperthermia. © 2015 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Effect of Cation Doping on the Superplastic Flow in Yttria-Stabilized Tetragonal Zirconia Polycrystals

The superplastic characteristics of various cation-doped yttria-stabilized tetragonal zirconia polycrystals (Y-TZP) were examined. For 1 mol% cation doping the true stress of Y-TZP is very dependent on the ionic radii of the doped cations; for instance, smaller cation radii give rise to lower true stress when compared with the other compositions for the same grain size, strain rate, and testing temperature. The altered true stress level must be due to the change in diffusivity of the accommodation process for grain boundary sliding caused by the addition of cations in ZrO₂. The strain to failure of the doped zirconia is affected by both ionic radius and valence of the dopant cations.     

Melatonin-Based Therapeutics for Neuroprotection in Stroke

The present review paper supports the approach to deliver melatonin and to target melatonin receptors for neuroprotection in stroke. We discuss laboratory evidence demonstrating neuroprotective effects of exogenous melatonin treatment and transplantation of melatonin-secreting cells in stroke. In addition, we describe a novel mechanism of action underlying the therapeutic benefits of stem cell therapy in stroke, implicating the role of melatonin receptors. As we envision the clinical entry of melatonin-based therapeutics, we discuss translational experiments that warrant consideration to reveal an optimal melatonin treatment strategy that is safe and effective for human application.     

Development Of Cvt Control System And Its Use For Fuel‐Efficient Operation Of Engine

Continuously variable transmission (CVT) provides an automobile with the ability to change the gear ratio continuously, which can then improve not only ride quality such as acceleration performance but also fuel‐efficiency. However, to take advantage of the ability, a control system that can precisely control the gear ratio is required. This paper proposes such a control system for a belt‐driven CVT system. For controller design, first the CVT system is modeled by analytical and experimental approaches. The resultant static and dynamic characteristics provide a nonlinear first‐order model with an uncertain time constant and time delay. The nonlinear steady‐state gain is adjusted to one by a gain‐scheduled pre‐compensator. Thereby the plant model becomes a linear first‐order lag system with a dead time. The next step is controller design using the plant model. To guarantee stability and control performance against the parameter variation and time delay, the μ‐synthesis, a robust control method, is employed for feedback control. In addition, a feedforward controller is incorporated into the feedback control system to obtain better output response. The feedforward controller is given by a combination of the inverse system of the plant and a reference model that gives desired output response. As a result, the control system becomes a two‐degree‐of‐freedom control system. To evaluate the performance of the control system and its effectiveness on the fuel‐efficiency, computer simulation and driving tests were conducted. The simulation and experiment results prove that the proposed control system can make the gear ratio track a reference output quickly and precisely in the presence of the uncertainties. The results also show that the control system improves fuel‐efficiency by changing the gear ratio so that the engine torque and its revolution speed can satisfy optimum‐efficiency operating condition.     

Development of new dosimetry using extended DNA fibers

We applied fluorescent microscopy to monitor the damage of DNA upon exposure to gamma radiation. Our developed dosimetry demonstrated that the number of breaks in DNA is proportional to the dose of the irradiation but is not dependent on dose rate of the irradiation and the GC content of DNA.     

Morphology and Mechanical Properties in Polymer Blends of Photocurable Polymer and Polycarbonate

Relationships between the morphologies and mechanical properties of binary blends of a photocurable polymer (2‐propenoic acid, (octahydro‐4,7‐methano‐1H‐indenediyl) bis(methylene)ester; DCA) and a linear polymer (poly(4,4′‐cyclohexylidene bisphenol carbonate); PCz) have been investigated. The blend films are prepared by in situ photopolymerization of homogeneous mixtures of a DCA‐monomer and PCz. The phase structure has been converted from a semi‐interpenetrating polymer networks (semi‐IPN) structure to a bicontinuous structure by controlling the cure temperature. Bicontinuous phase‐separated structures can be obtained by curing a wide range of compositions of 17–50 wt.‐% PCz at high temperatures. Miscible semi‐IPN structures are attained by means of photopolymerization below the glass transition temperature of the homogenous mixture before performing photoirradiation, such that magnetic relaxation measurements showed the blend to be miscible in the 10 nm order. The tensile strength and modulus reached a maximum in those blends having an intermediate vague phase structure between semi‐IPN and bicontinuous structures that have a strong interfacial interaction, which leads to incomplete phase decomposition in the PCz‐rich matrix phase. The maximum strength and modulus prepared under optimum condition are inferior to those of the individual components. In contrast, the elongation and break energy are greatly improved in those blends with bicontinuous structures having a diffused phase boundary.

DCA‐rich domain size in bicontinuous structure for DCA/PCz system, as a function of cure temperature; (□) 17 wt.‐% PCz, (○) 30 wt.‐% PCz, and (?) 50 wt.‐% PCz.     

Springback evaluation of friction stir welded TWB automotive sheets

Springback behavior of automotive friction stir welded TWB (tailor welded blank) sheets was experimentally investigated and the springback prediction capability of the constitutive law was numerically validated. Four automotive sheets, aluminum alloy 6111-T4, 5083-H18, 5083-O and dual-phase DP590 steel sheets, each having one or two different thicknesses, were considered. To represent mechanical properties, the modified Chaboche type combined isotropic-kinematic hardening law was utilized along with the non-quadratic orthogonal anisotropic yield function, Yld2000-2d, while the anisotropy of the weld zone was ignored for simplicity. For numerical simulations, mechanical properties previously characterized [1] were applied. For validation purposes, three springback tests including the unconstrained cylindrical bending, 2-D draw bending and OSU draw-bend tests were carried out. The numerical method performed reasonably well in analyzing all verification tests and it was confirmed that the springback of TWB as well as of base samples is significantly affected by the ratio of the yield stress with respect to Young’s modulus and thickness.     

Oxidative coupling polymerization of racemic 3,3’-dihydroxy-2,2’-dimethoxy-1,1’-binaphthalene with copper(II)-(-)-sparteine complex

Summary The oxidative coupling polymerization of racemic 3,3’-dihydroxy-2,2’-dimethoxy-1,1’-binaphthalene with copper(II) chloride-(-)-sparteine [(-)Sp] in methanol at room temperature was carried out and the enantiomer-selectivity during the polymerization was examined. The (R)-monomer preferentially reacted, and the purity of the unreacted monomer reached 80%ee (S) after 15 h, while that of the polymerized monomer gradually decreased from 26%ee (R) as a function of the polymerization. The ratio of the rate constants of both enantiomers, s=k_R/k_S, was determined to be 2.3. The model coupling reaction of the mono-benzylated (R)-monomer with CuCl₂-(-)Sp showed that the R-configuration with respect to the carbon-carbon bonds between the monomer units was selectively constructed during the polymerization.