高能 X 射线工业 CT 技术的研究进展

目的 研究分析了国内外高能X射线工业CT技术的进展情况，方法 通过有关文献资料，对目前国际上主要的高能X射线工业CT技术及设备进行评述。结果和结论 对美国、德国等发达国家的高能X射线工业CT设备、线阵探测器、面陈探测器及重建算法进行了分析。     

ARTIFICIAL INTELLIGENCE CONTROL OF FOOD FREEZER USING ROTATING DISK AIR DISTRIBUTOR FOR UNIFORM FREEZING

A rotating disk air distribution (RDAD) system consisting of a rotating disk with an air supply hole was fabricated to solve the nonuniform freezing problem of a freezer that supplies air through a duct at a fixed location. The RDAD system was installed in a freezer to supply freezing air in various directions by controlling the position of the air supply hole. An equation estimating air velocity in the freezer was developed based on heat balance between a brass block thermocouple (BBT) probe and ambient air stream. The equation was applied to the analysis of airflow patterns developed through the RDAD and the fixed duct system. For control of the RDAD system, a fuzzy matrix was constructed with the measured nodal temperature at 3D locations in the freezer and used to search for the optimum direction of air supply. Uniform cooling was accomplished with the RDAD system using fuzzy and expert algorithms leading to temperature deviation σ=0.666, compared with 0.289 of the fixed air supply system. Cooling rate of model food (BBT) was 1.75 times faster than that of the fixed system.     

Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

“镍”催化酰氯和有机锡试剂交叉偶联反应的研究

镍络合物催化酰氯与有机锡试剂交叉偶联合成有机酮的反应,其反应选择性强,反应彻底,转化率高,工艺简单。在有机锡过量的情况下,对不同催化剂的催化活性和包括投料比,反应温度,反应时间,反应溶剂等反应条件进行了考察。     

The effects of plasma etching induced gate oxide degradation onMOSFET's 1/f noise

The effects of the plasma etching process induced gate oxide damages on device's low frequency noise behavior are investigated on MOSFET's fabricated with different field plate perimeter to gate area ratio antennas. Abnormal 1/f noise spectrum with a shoulder centered in the frequency range of 100 and to 1 kHz was frequently observed in small geometry devices, and it is attributable to a nonuniform distribution of oxide traps induced by plasma etching process     

能量"三环节"理论在原油蒸馏装置扩能改造中的应用

中国石化扬子石化股份有限公司炼油厂在第一套常减压蒸馏装置扩能改造中，使用了多项节能技术以实现能量的优化利用。本文以标定数据为基础，运用能量“三环节”理论对该装置的用能状况进行了计算和分析，从能量利用角度对装置的扩能改造效果进行了评价，并为装置的进一步优化能量利用提出了相应措施。     

丁烷脱沥青装置掺炼油浆工艺

由于新疆原油的渣油中重金属含量高，结构组成复杂，直接进入催化裂化装置做原料时，催化剂重金属污染严重，产品分布差，渣油掺炼量低。而且，丁烷脱沥青过程所得到的脱油沥青软化点高、针入度低、延伸度差。为了提供优质的催化裂化原料和优质的道路沥青原料，进行了丁烷脱沥青装置掺炼油浆组合工艺的开发和应用，取得了较好的效果，脱沥青油收率提高，提供了更多重金属含量低的催化裂化原料，沥青性能得到改善。     

井下减速器传动方案分析

结合井下减速器的结构特点，分析了定轴轮系传动、2K-H型行星轮系传动、3K行星轮系传动、少齿差行星轮系传动4种传动方案，选择内齿作为输出轴的少齿差行星轮系传动方案更符合涡轮钻具的传动要求和井下工具结构特点。少齿差行星轮系的研制、开发、应用可降低涡轮钻具转速，提高扭矩，提高深井钻速。     

龙开口水电站溢流坝段动力模型破坏试验研究

采用仿真混凝土材料研究了龙开口水电站溢流坝段在不同因素影响下的动力破坏特征,并通过对6个模型试验结果的分析探讨了溢流坝段的动力破坏机理。试验中考虑了坝体-库水的动力相互作用以及横河向地震动对大坝破坏的影响,采用规范谱波和场地谱波两种地震动激励进行模型超载破坏分析。试验结果为工程设计和评价溢流坝段的抗震性能提供依据。