Experimental investigation of a pulsating heat pipe for hybrid vehicle applications

This paper deals with the experimental results of an unlooped pulsating heat pipe (PHP) developed and tested in an electronic thermal management field with hybrid vehicle applications in mind. The 2.5 mm inner tube diameter device was cooled by an air heat exchanger to replicate the environment of a vehicle.In order to characterize this pulsating heat pipe, four working fluids have been tested. They are acetone, methanol, water, and n-pentane, with applied thermal power ranging from 25 W to 550 W, air temperature ranging from 10 °C to 60 °C and air velocity ranging from 0.25 m s^?1 to 2 m s^?1. Three inclinations have also been tested according to their horizontal positions: +45° (condenser above the evaporator), 0° and ?45° (condenser below the evaporator).Among the different results, some of the most revelatory were obtained with regard to unfavourable inclination (?45°), for which the performances were very interesting considering a terrestrial application. On the other hand, one also observed low temperature limitations for water as a working fluid and degradation of performances for n-pentane tested at 60 °C air temperature. On an overall basis, however, it should be noted that the PHP functioned with high reliability and reproducibility and without any failure during the start-up or working stage.     

Thermal behavior of an electrical motor through a reduced model

The aim of this study is to obtain quickly thermal information on some sensitive components of an electrical motor in a short lapse of time. The thermal behavior of this complex system is modeled and validated. The corresponding detailed model leads to the resolution of a linear system of differential equations of high order, but is not easy to handle for control purposes, due to long CPU time. In order to compute faster, two model reduction techniques are used: the Eitelberg method and the reduction by modal identification. The reduced models effectively give good temperature accuracy on the critical points of the motor with very fast computation time     

Design Impact on Airflow Patterns in Fluidization Units

The airflow behavior in a fluidization unit was integrally studied by means of experimental work and computational fluid dynamics simulation. The computational domain included the gas inlet pipe, plenum, perforated plate, fluidization chamber, and air outlet pipe. Different scenarios were simulated to allow distinguishing the best way to represent perforated‐plate distributors and elucidate the impact of the grid design on the fluidization performance. The simulated pressure drop across the distributor and the plenum flow pattern were in concordance with the experimental data. It was found that the distance between the peripheral holes and walls has a great impact on the airflow downstream the distributor.     

Topological planning and design of UMTS mobile networks: a survey

In this paper, we present a literature review on the topological planning problem of third generation (3G) cellular networks based on the universal mobile telecommunications system (UMTS) standard. After describing the UMTS architecture, we introduce each subproblem and present major works that have been done. The cell, the access and the core network planning problems have all been considered as well as a more global approach (when more than one subproblems are considered simultaneously). Both planning and expansion algorithms are also included in this review. The goal of this paper is to present and classify the different research works that have been done so that it can be used as a starting point for future research on topological design of UMTS networks. Copyright © 2008 John Wiley & Sons, Ltd.     

Best management practices for corporate, academic and governmental transfer of sustainable technologies to developing countries

Innovations with respect to technologies that contribute to environmental sustainability have emerged within national government laboratories, international agencies and within academic research institutes. Since each of these entities is understandably more focused on ab initio research, conceptual development and proofs of concept, the production level manufacturing and broad dissemination of such technologies require development of best management practices (BMPs) for effective partnerships with and/or technology licensure to private sector industry. Alternatively, certain technologies that address specific environmental sustainability needs within the developing countries can be and have been transferred directly, either through bi-lateral transfers or through multi-lateral agencies, serving as intermediaries. The appropriateness of such transfers is contingent upon host country environmental, cultural and socio-political conditions, the type of technology involved, the “terms of transfer” and the relationships established between the technology conceivers and the end-users. The authors select examples of identified modes of sustainable technology transmission and derive experiential BMPs, which may be of some utility for future sustainable technology transfer. Moreover, in providing these BMPs, the historical record and contemporary caveats with respect to unregulated technology transfer, whether sustainable or otherwise, to developing countries and the array of corresponding proposed codes of conduct are examined, given the normative objective that such technologies should ultimately contribute to ecologically benign and societally beneficial objectives, such as environmental sustainability, equitable growth and poverty alleviation. These issues and the need to establish BMPs would be broadly relevant with the new focus on climate change-related technology funds and associated regional impact projects evolving across the globe and within the developing countries in particular.     

Bioefficacy of essential and vegetable oils of Zanthoxylum xanthoxyloides seeds against Acanthoscelides obtectus (Say) (Coleoptera: Bruchidae)

Experiments were conducted in the laboratory to evaluate the bioefficacy of essential and vegetable oils of Zanthoxylum xanthoxyloides (Rutaceae) against Acanthoscelides obtectus (Coleoptera: Bruchidae). The chemical composition of the essential oil and the fatty acid composition of the vegetable oil extracted from the seeds of Z. xanthoxyloides were determined. The insecticidal activities of these oils and the associated aromatized clay powder were evaluated against A. obtectus. Both oils were strongly repellent (100% repellency at 0.501 μl/cm2 essential oil and 3.144 μl/cm2 vegetable oil) and highly toxic (LC?? = 0.118 μl/cm2 for essential oil) to this beetle after contact on filter paper. The vapors of the essential oil were highly toxic to adult insects (LC?? = 0.044 μl/cm3), and the aromatized powder made from clay and essential oil was more toxic (LD?? = 0.137 μl/g) than the essential oil alone (LD?? = 0.193 μl/g) after 2 days of exposure on a common bean. Both oils greatly reduced the F? insect production and bean weight loss and did not adversely affect the bean seed viability. In general, the results obtained indicate that these plant oils can be used for control of A. obtectus in stored beans.     

Structure and properties of sugar beet fibres

Fibrous fractions were prepared from sugar beet pulp (RF) by sequential extractions with potassium oxalate, 0.05 M hydrochloric acid at 85°C and 0.05 m sodium hydroxide at 4°C. The overall composition, polysaccharide structure and some physico-chemical properties (cation exchange capacity, CEC; water holding capacity, WHC; swelling) of each fraction were determined. RF was mostly composed of carbohydrates (66.3 %) with minor amounts of ash, proteins and lignin. The main polysaccharides were highly methylated and acetylated pectins, cellulose and arabinans. The oxalate residue (82.1 % of RF) exhibited only minute differences from RF whereas the acidic and alkaline residues, accounting for 42.8 % and 35.5 % of RF, respectively, were enriched in cellulose and hemicelluloses (xylans, xyloglucans, mannans) and mostly devoid of pectins and arabinans. CEC and WHC of fractions were closely related to the content of unmethylated galacturonic acid residues. The influence of the ionic form of ionisable groups was demonstrated, the Na⁺ form giving the highest WHC. The ionic strength of the medium can reduce the WHC, especially in the case of the acid and alkali-extracted fibres.     

A formal framework for multi-agent systems analysis and design

Agent based computing is generally intended for modeling and implementation of distributed complex problems. Despite the existence of many applications, the problem of rational engineering of multi-agent systems remains complex and difficult. The purpose of this paper can be summarized within two claims. First, we aim at providing an approach that gives some guidelines for specifying and designing multi-agent systems. Secondly, we focus on the formalisms as a language for describing the models produced in each development process phases. These seem to be straightforward, while the development of multi-agent systems is still done, in most cases, without using methods and formal modeling such as those generally used in object oriented software. We illustrate this approach by specifying an example based upon a specific agent architecture.     

A metamodeling approach for the identification of organizational smells in multi-agent systems: application to ASPECS

Software Quality is one of the most important subjects in the Process Development Software, especially in large and complex systems. Much effort has been devoted to the development of techniques and concepts to improve software quality over the years. We are especially interested on smells, which represent anomalies or flaws in the design/code that can have serious consequences in maintenance or future development of the systems. These techniques have a strong development in the Object Oriented paradigm, however, very few studies were conducted in the agent oriented paradigm. In this paper we focus on the detection of design smells applied to multi-agent systems models based on the organizational approach, named Organizational Design Smells (ODS). Early and automatic detection of these ODS allows reducing the costs and development times, while increasing the final product’s quality. To achieve this objective, validation rules were defined based in the EVL language. The approach is illustrated with two examples, their validation rules, and the refactoring solutions proposed.     

Electronic structure and conformations of ortho-, meta-, and para-aminobenzensulfonic acid and its dimers

Geometric and electronic structures of some aniline derivatives have been obtained, aimed at a microscopic explanation of the observed electropolymerizability of these compounds. Monomers, dimers and their corresponding free radicals and ionic species, with the sulfonic acid group substituent located at various positions on the benzenoid ring, are considered. In this work we present an ab initio post-Hartree-Fock and density functional study of the ortho-, meta- and para-isomer of aminobenzenesulfonic acid (ortho-, meta-, and para-ABSA). To envisage a possible coupling scheme between ABSA molecules, we have obtained the equilibrium geometry and the electronic structure for monomers and dimers of ABSA as well as for the corresponding free radicals and ions.Based on the monomer-optimized geometries, atomic charges, bond orders and spin densities, a coupling scheme in the electrochemical polymerization is suggested. We have also calculated band gaps and ionization potentials. Some comments concerning the different theoretical methods used are made.