Ru-catalyzed anode materials for direct hydrocarbon SOFCs

A solid oxide fuel cell using a thin ceria-based electrolyte film with a Ru-catalyzed anode was directly operated on hydrocarbons, including methane, ethane, and propane, at 600 °C. The role of the Ru catalyst in the anode reaction was to promote the reforming reaction of the unreacted hydrocarbons by the produced steam and CO₂, which avoided interference from steam and CO₂ in the gas-phase diffusion of the fuels. The resulting peak power density reached 750 mW cm⁻² with dry methane, which was comparable to the peak power density of 769 mW cm⁻² with wet (2.9 vol.% H₂O) hydrogen. More important was the fact that the cell performance was maintained at a high level regardless of the change in the methane utilization from 12 to 46% but was significantly reduced by increasing the hydrogen utilization from 13 to 42%. While the anodic reaction of hydrogen was controlled by the slow gas diffusion, the anodic reaction of methane was not subject to the onset of such a gas-diffusion process.     

Effect of chromium content on remarkably rapid nitriding in austenitic Fe-Ni-Cr alloys

Remarkably rapid nitriding which is independent of diffusion theory based on the thermal activation process, was observed during nitriding of austenitic Fe-Ni-Cr steels containing 16 and 19 mass% chromium. Increase of the chromium content in the alloys yielded increasing thickness of the nitrided layer, i.e. the internal nitriding theory did not hold in the nitriding. No rapid nitriding was observed in steels containing less than 13 mass% chromium. Hence the limiting concentration of chromium for the rapid nitriding will lie between 13 and 16 mass% chromium. A solution to the problem of abnormalities arising during nitriding of practical austenitic stainless steels which have been investigated since 1972, has been presented experimentally by nitriding various chromium-containing steels. Based on the experimental results, the origin of the rapid nitriding is discussed in connection with the free-energy function of Cr₂N and CrN to temperature. In particular, a plateau of nitrogen concentration measured in the nitrided layers leads to the conclusion that a forced nitrogen diffusion in the layer resulted in the rapid nitriding.     

Solid-Phase Syntheses of Two Deacetyl-Thymosin β4 Analogues with Substitution at Position 12 and Their Effects on Impaired Blastogenic Response of T Lymphocytes of Uremic Patients

Two deacetyl-thymosin β₄ analogues containing Phe(4Br) or D-Phe(4Br) as position 12 were synthesized by the manual solid-phase method, and their immunological effects on the impaired blastogenic response of phytohemagglutinin-stimulated T lymphocytes of uremic patients with infectious diseases were studied. Bromination of the p-position of Phe¹² resulted in a marked restorative effect on the impaired blastogenic response of T lympocytes compared with that of our synthetic deacetyl-thymosin β₄ The synthetic [Phe(4Br)¹²]deacetyl-thymsin β₄ was approximately equal in potency to our synthetic [Phe(4F)¹²]deacetyl-thymosin β₄ in uremic patients, but the other analogue, [D-Phe(4Br)¹²]deacetyl-thymosin β₄, had no effect.     

Effects of nondensifying inclusions on the densification and microstructure of zinc oxide matrix composites

The densification and microstructure development of ZnO containing Zn₇Sb₂O₁₂, ZrO₂, and aggregated ZnO were investigated to elucidate the effect of nondensifying inclusions on the sintering of ceramic/ceramic composites. The inclusion retarded the densification, and the degree of retardation was found to depend on the chemical species of inclusion; Zn₇Sb₂O₁₂ had the largest effect, followed by ZrO₂ and then aggregated ZnO last. The experimental results for aggregated ZnO was explained by the theory which predicts the generation of backstresses. The backstresses give a less significant effect on the densification. For Zn₇Sb₂O₁₂ and ZrO₂, the microstructure of the matrix varied with distance from an inclusion particle; much porosity was observed in the region surrounding the inclusion. Circumferential voids, which are responsible for the suppression of densification, form during the initial stage of sintering. Inclusion particles generate an anchoring effect which retards the densification of the matrix immediately surrounding the inclusion particle during the intermediate stage.Supported by the Inamori Foundation.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Schottky barrier heights of contact metals to p-type ZnSe

Schottky barrier heights (SBHs) of a variety of metals (In, Cd, Nb, Ti, W, Cu, Ag, Au, Ni, Pt, and Se) contacting to p-ZnSe grown by a molecular beam epitaxy method were determined by analyzing capacitance-voltage (C-V) and/or current density-voltage (J-V) curves. The SBH values of the Au and Ni contacts were determined from intersections of straight lines of the C⁻²-V curves to be 1.23 and 1.13 eV, respectively. The J-V calculations provided a large SBH value of 1.2 ± 0.1 eV for a variety of metals, indicating that the Fermi-level could be pinned at the contact interface. Reduction of the SBH values to a level lower than 0.4 eV and/or increase of doping concentrations to a level higher than 10²⁰ cm⁻³ are essential to obtain an ohmic contact with contact resistivity of around 10⁻³ Ω·cm².     

Preparation of SiB4±x and SiB6 plates by chemical vapour deposition of SiCl4 + B2H6 system

SiB_4±x and SiB₆ plates were prepared by chemical vapour deposition (CVD) using SiCl₄, B₂H₆ and H₂ gases under the conditions of deposition temperatures (T _dep) from 1323–1773 K, total gas pressures (P _tot) from 4–40 kPa and B/Si source gas ratio (m _B/Si=2B₂H₆/SiCl₄) from 0.2–2.8. The effects of CVD conditions on the morphology, structure and composition of the deposits were examined. High-purity and high-density SiB_4±x and SiB₆ plates about 1 mm thick were obtained at the deposition rates of 71 and 47 nm s⁻¹, respectively. The lattice parameter, composition and density of CVD SiB_4±x plates were dependent on their non-stoichiometry. The lattice parameter,a, was 0.6325 nm, butc ranged from 1.262–1.271 nm.The B/Si atomic ratio ranged from 3.1–5.0, and the density ranged from 2.39–2.45×10³ kg m⁻³. The CVD SiB₆ plates showed constant values of lattice parameters (a=1.444 nm,b=1.828 nm,c=0.9915 nm), composition (B/Si=6.0) and density (2.42×10³ kg m⁻³), independent of CVD conditions.     

High performance liquid chromatographic separation of stereoisomeric bile acids as their UV-sensitive esters

High performance liquid chromatographic separation of a series of mono-, di- and trihydroxylated 5β-cholanic acids which differ only in position and configuration of hydroxyl groups at positions C-3, C-7 and/or C-12, is reported. The C-24 free acids were derivatized to four different classes of UV-sensitive esters, i.e.,p-bromophenacyl (BP),m-methoxyphenacyl (MP), 4-nitrophthalimidemethyl (NPM) and 9-anthrylmethyl (AM) esters, and chromatographed on two, variants of C₁₈ reversed-phase columns (Nova-Pak C₁₈ and Zorbax ODS) with methanol-water systems as mobile phase. Separation efficiency and elution order of some isomeric pairs were influenced by both the structure of the C-24 ester groups and the nature of the columns used. Excellent chromatographic properties were found for those derivatives, particularly for the NPM esters.