Prognostic evaluation of early indicators in fulminant hepatic failure by multivariate analysis

Results of eight multicenter, randomized, placebo-controlled, double-blind, parallel-group studies were pooled to assess the efficacy of the angiotensin II-receptor blocker irbesartan over the dose range of 1 to 900 mg. A total of 2955 adults with a seated diastolic blood pressure of 95 to 110 mm Hg were randomized to treatment with oral irbesartan once daily or placebo for 6 to 8 weeks. Office blood pressure was measured at trough (24+/-3 hours after the last dose) and peak (3+/-1 hours after the last dose) by mercury sphygmomanometry. Demographic characteristics (mean blood pressure; 151/101 mm Hg; mean age, 54 years; 63% male; and 82% white) were similar across all dose groups. After the groups were pooled, antihypertensive efficacy was assessed by therapeutic response (trough seated diastolic blood pressure <90 mm Hg or a reduction from baseline of > or = 10 mm Hg) and by modeling of the maximum reductions in trough and peak seated diastolic and systolic blood pressure. Antihypertensive effects increased with increasing doses and reached a plateau at > or = 300 mg. Irbesartan 150 mg provided placebo-subtracted reductions in trough seated systolic and diastolic blood pressure of approximately 8 and approximately 5 mm Hg, respectively, with 56% of patients displaying a favorable response. In conclusion, irbesartan provides clinically significant blood pressure lowering, with a clear relationship between (log) dose and antihypertensive effect.     

Correction to: EDVWDD: Event‑Driven Virtual Wheel‑based Data Dissemination for Mobile Sink‑Enabled Wireless Sensor Networks

The Journal of Supercomputing - A correction to this paper has been published: https://doi.org/10.1007/s11227-021-03790-9     

DDFSGEN

This paper presents a functional compiler for the automatic design of Direct Digital Frequency Synthesizer (DDFS) integrated circuits (ICs) using a ROM based table look-up architecture. The compiler allows the user to specify high-level specifications such as the acceptable spurious response and it generates the IC architecture, floorplan, and layout. To construct the layout for different specifications, a library of parameterized macrocells has been developed in 1.2 m CMOS technology.A test chip with a quadrature DDFS module has been generated, using the compiler, and fabricated. The chip has two input signals: one is for frequency control while the other is for phase initialization. Input and output word lengths are 16 bits and 6 bits respectively. The chip complexity is approximately 12,000 transistors (DDFS core) and the die size is 4.8×2.9mm ². A maximum sample rate of 80 MHz has been attained implying a maximum sine (cosine) output frequency of 40 MHz and a frequency resolution of 1.22 kHz. The maximum spurious level measured is –46 dB.     

Sparse decompositions for exploratory pattern analysis

We define and verify the utility of a pattern analysis procedure called sparse decomposition. This technique involves sequentially ``peeling' sparse subsets of patterns from a pattern set, where sparse subsets are sets of patterns which possess a certain degree of regularity or compactness as measured by a compactness measure c. If this is repeated until all patterns are deleted, then the sequence of decomposition ``layers' derived by this procedure provides a wealth of information from which inferences about the original pattern set may be made. A statistic P is derived from this information and is shown to be powerful in detecting clustering tendency for data in reasonably compact sampling windows. The test is applied to both synthetic and real data.     

Catalytic oxidation of methanol over molybdenum oxide–tungsten oxide

The vapour phase oxidation of methanol to formaldehyde over molybdenum oxide, tungsten oxide and their mixtures has been investigated in an integral flow reactor at atmospheric pressure. The effect of several process variables on the conversion and yield were determined. A high conversion of 95.6% methanol with nearly 95% selectivity was obtained at 430°C. A rate expression has been derived from the kinetics of the reaction.     

2-DOF vibratory gyroscope fabricated by SU-8 based UV-LIGA process

This paper reports fabrication of 2-DOF vibratory gyroscope using SU-8 based UV-LIGA process. The device structure is designed to be symmetrical in order to match the resonance frequencies of drive and sense mode oscillators and also to minimize their relative temperature dependent drift. The overall arrangement is such that the two vibration modes do not affect each other and therefore, mechanical decoupling is achieved which helps in minimizing bias drift. The design is optimized to be compatible with the UV-LIGA process having 10 μm thick electroformed nickel as structural layer. Photolithography to create 11 μm thick SU-8 molds for electroforming sacrificial copper and structural nickel layer is optimized using multiple exposure technique that ensures near vertical side walls. Since the highly cross-linked SU-8 remaining after development is difficult to remove reliably from high aspect ratio structures without damage or alteration to the electroformed metals, a 2.45 GHz MW plasma etching process is developed with CF₄/O₂ mixes. The fabricated device is checked for off-plane misalignment between the stationary and movable comb fingers using white light interferometry and it is found to be almost negligible. Also, the prototype device is characterized for amplitude and phase spectral responses using Polytec MSA-500 Micro System Analyzer. The drive and sense mode resonance frequencies are observed at 7.3 and 7.1 kHz respectively against the mode matched designed frequency of 7.5 kHz.     

Thermal degradation of cellulose and its phosphorylated products in air and nitrogen

The thermal degradation of cellulose and its phosphorylated products (phosphates, diethylphosphate, and diphenylphosphate) were studied in air and nitrogen by differential thermal analysis and dynamic thermogravimetry from ambient temperature to 750°C. From the resulting data various thermodynamic parameters were obtained following the methods of Broido and Freeman and Carroll. The values of E_a for decomposition for phosphorylated cellulose were found to be in the range 55–138 kJ mol^?1 in air and 85–152 kJ mol^?1 in nitrogen and depended upon the percent of phosphorus contents in the samples. The mass spectrum of cellobiose phosphate indicated the absence of the molecular ion, indicating that the compound was thermally unstable. The IR spectra of the pyrolysis residues of cellulose phosphate gave indication of formation of a compound having C?O and P?O groups. A fire retardancy mechanism for the thermal degradation of cellulose phosphate has been proposed.     

A class of discontinuous dynamical systems IV. A laboratory air-water system

An air-water experimental system consisting of two inlets and one outlet is constructed and characterised. It reaches the state of sliding mode, or equivalently, two phase slug flow. The linear hydraulic model proposed in the literature is adequate to describe it. Experimental data are used to tune this model. The resistance to the flow of air through the outlet valve during the two phase flow is much larger than that when air alone flows out. At the operating range, the resistance to water flow is not affected by the presence of air.     

A piezoelectric model based multi-objective optimization of robot gripper design

The field of robotics is evolving at a very high pace and with its increasing applicability in varied fields, the need to incorporate optimization analysis in robot system design is becoming more prominent. The present work deals with the optimization of the design of a 7-link gripper. As actuators play a crucial role in functioning of the gripper, the actuation system (piezoelectric (PZ), in this case) is also taken into consideration while performing the optimization study. A minimalistic model of PZ actuator, consisting different series and parallel assembly arrangements for both mechanical and electrical parts of the PZ actuators, is proposed. To include the effects of connector spring, the relationship of force with actuator displacement is replaced by the relation between force and the displacement of point of actuation at the physical system. The design optimization problem of the gripper is a non-linear, multi modal optimization problem, which was originally formulated by Osyczka (2002). In the original work, however, the actuator was a ‘constant output-force actuator model’ providing a constant output without describing the internal structure. Thus, the actuator model was not integrated in the optimization study. Four different cases of the PZ modelling have been solved using multi-objective evolutionary algorithm (MOEA). Relationship between force and actuator displacement is obtained using each set of non-dominated solutions. These relationships can provide a better insight to the end user to select the appropriate voltage and gripper design for specific application.