Calciothermic reduction of titanium oxide in molten CaCl<Subscript>2</Subscript>

Titanium oxides were reduced to metallic titanium using the liquid calcium floating on the molten CaCl₂. A part of Ca dissolved into CaCl₂ and reacted with TiO₂ settled below CaCl₂. The by-product CaO also dissolved by about 20 mol pct into CaCl₂, which was effective in reducing the oxygen concentration in the obtained Ti particles. The compositional region in the Ca-CaCl₂-CaO system was examined for the less oxygen contamination in Ti and the better handling in leaching. A large amount of the residual calcium oxidized the titanium powder in leaching. The metallic Ti powder less than 1000 mass ppm oxygen could be obtained only for 3.6 ks using 5 to 7 mol pct Ca-CaCl₂ at 1173 K. The powder was slightly sintered like sponge, and contained approximately 1500 ppm Ca. The anatase phae, the intermediate product in the refining process of TiO₂, could be also supplied as raw material as well as rutile.     

Photoresponsive peptide and polypeptide systems: part II. Photochromism of poly(l-ornithine) containing various azo-contents in side chains

Poly(L-ornithine)s having various azo-contents in the side chains were synthesized by the water-soluble carbodiimide procedure. The photochemical properties of the polypeptides poly[N^δ-p-(phenylazo)benzoyl-L-ornithine] (PPABLO) containing 3–77 mol% azobenzene were investigated by absorption and circular dichroism spectroscopy in hexafluoro-2-propanol (HFIP) or water, and in HFIP-water or methanol-water solvent mixtures. The photochromism of the dichroic bands of the PPABLOs containing 20–77 mol% azobenzene in the visible and ultraviolet wavelength regions was found to be mostly reversible as a function of irradiation time at different wavelengths due to the photostationary state (above 80% trans-cis photoisomerization) of the azo aromatic moieties. The PPABLO containing 3.2 mol% azobenzene in water exhibited conformational changes from random coil to helix by the addition of methanol or sodium dodecyl sulphate (SDS). The photo-induced conformational change was observed in HFIP-water-SDS solvent mixtures, while no conformational change was seen in water and HFIP-water solvent mixtures.     

Dynamic stress intensity factors analysis of interface crack using line-spring model

In this study, a new method for calculating the dynamic stress intensity factors of a bimaterial bending specimen with an interface crack is proposed by making use of a line-spring model. A pre-cracked bending specimen is modeled by one-dimensional beam finite elements and a line-spring representing the stiffness or compliance of a cracked part. The proposed method enables the one-dimensional analysis of a two-dimensional crack problem; thus the time variations of the dynamic stress intensity factors of a bimaterial bending specimen with an interface crack can be obtained by making use of a personal computer within a few minutes. The results obtained by the proposed method agree reasonably well with those obtained by the two-dimensional finite element method, although a slight difference in period can be found. The proposed method enables rapid evaluation of dynamic stress intensity factors. So a rapid evaluation system of the dynamic fracture toughness of a bimaterial with an interface crack can be achieved by combining an instrumented impact test apparatus with a computer program based on the proposed method which runs on a personal computer.     

Image compression in digital mammography: effects on computerized detection of subtle microcalcifications

Our previous receiver operating characteristic (ROC) study indicated that the detection accuracy of microcalcifications by radiologists is significantly reduced if mammograms are digitized at 0.1 mm x 0.1 mm. Our recent study also showed that detection accuracy by computer decreases as the pixel size increases from 0.035 mm x 0.035 mm. It is evident that very large matrix sizes have to be used for digitizing mammograms in order to preserve the information in the image. Efficient compression techniques will be needed to facilitate communication and archiving of digital mammograms. In this study, we evaluated two compression techniques: full frame discrete cosine transform (DCT) with entropy coding and Laplacian pyramid hierarchical coding (LPHC). The dependence of their efficiency on the compression parameters was investigated. The techniques were compared in terms of the trade-off between the bit rate and the detection accuracy of subtle microcalcifications by an automated detection algorithm. The mean-square errors in the reconstructed images were determined and the visual quality of the error images was examined. It was found that with the LPHC method, the highest compression ratio achieved without a significant degradation in the detectability was 3.6:1. The full frame DCT method with entropy coding provided a higher compression efficiency of 9.6:1 at comparable detection accuracy. The mean-square errors did not correlate with the detection accuracy of the microcalcifications. This study demonstrated the importance of determining the quality of the decompressed images by the specific requirements of the task for which the decompressed images are to be used. Further investigation is needed for selection of optimal compression technique for digital mammograms.     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Recovery of monomers and fillers from high-temperature-vulcanized silicone rubbers—combined effects of solvent, base and fillers

The depolymerization of high-temperature-vulcanized (HTV) silicone rubbers containing filler silica and alumina into cyclosiloxane monomers and spontaneous recovery of fillers were studied. First, HTV silicone rubber was treated with different types of solvents in the presence of KOH to find that a triad mixture of diethylamine, methanol and hexane was appropriate not only to dissolve the silicone rubber to a suspension but also to separate fillers completely by filtration. The filtrate was distilled to remove solvent first and then give pure cyclosiloxane monomers in 76–84% yields. Second, the rubbers were treated with other types of triad mixture of solvents and bases, e.g. tetramethylammonium hydroxide, hexane and diethylamine. After filtration, residue was again treated with the amine and hexane to recover clean fillers in 83–93% yields. Cyclosiloxane monomers were also obtained from the combined filtrates in 67–78% yields.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.