FF现场总线的网段负载能力的设计及计算

从生产安全运行的管理要求；电压压降和电流的限制及信号的衰减；网络运行时间的要求；系统设计的影响；备用能力的考虑等各个方面，结合上海赛科聚苯乙烯项目的具体设计，分析隔爆条件下FF现场总线的H1网段负载能力的设计，以供大家探讨。     

地下埋藏式钢岔管抗外压稳定性分析

考虑了钢岔管与混凝土垫层的初始缝隙和初始几何缺陷,给出了一套地下埋藏式钢岔管抗外压稳定性的三维有限元分析和求解方法。采用该方法分析某工程实例,将其成果与阿氏公式计算的结果进行了比较,证明了该方法的可行性,并得到一些对工程设计有参考价值的成果。     

电调整微蚀刻

评述了采用电调整微蚀刻试验表明,它适用于各种各样的线宽和间距的精细导线的制造。比起常规喷射蚀刻工艺来,其侧蚀小、蚀刻因子和tanθ高的效果。     

He-Ne激光自混合干涉的模式研究

对一般He—Ne激光和频率分裂激光器中偏振态相互垂直的o光和e光的自混合于涉的模式进行了研究，发现了单模变三模的现象，并进行了解释。     

在无铅环境中的热风整平

当电子工业走向无铅焊接的时候,热风焊料整平仍然是继续可焊性保护的优选方法。     

琼东南盆地深水区储层分布规律

琼东南盆地深水区经历了断陷、断拗和拗陷3大构造演化和沉积充填阶段,主要发育4种沉积体系,相应地形成了4类主要储层:1)陵三段扇三角洲或滨海相砂岩储层;2)三亚、梅山组滨浅海相砂岩储层;3)三亚—莺黄组低位体储层;4)梅山组台地边缘礁滩灰岩储层。平面上,储层发育具有明显的分带性,可划分为:北部浅水陆架滨岸砂岩、三角洲砂岩储层发育带;中央坳陷低位体储层发育带;南部永乐隆起区碳酸盐岩储层发育带。深水区主要位于后2个带,每个带储层发育的控制因素不同,可以进一步划分为多个储层发育区。每个储层发育区存在多套储盖组合,每套储盖组合在多个储层区中发育。其中台地灰岩储层可能成为南部隆起区具有重要意义的勘探层系。      

Flash器件中氧化硅/氮化硅/氧化硅的特性

对普遍采用的氧化硅/氮化硅/氧化硅( ONO)三层复合结构介质层的制备工艺及特性进行了研究分析,研究了ONO的漏电特性以及顶氧( top oxide)和底氧( bottom oxide)的厚度对ONO层漏电的影响.结果表明,采用较薄的底氧和较厚的顶氧,既能保证较高的临界电场强度,又能获得较薄的等效氧化层厚度,提高耦合率,降低编程电压.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.