Analysis of resistive bridging fault detection in BiCMOS digitalICs

This paper presents a study of the effects on the electrical behavior of BiCMOS digital circuits induced by bridging faults, whose resistance value is shown to have a strong impact on the static and dynamic behavior of faulty gates and of their fan-out gates. The problem of fault detection is addressed considering different testing techniques (current monitoring, functional, and delay testing). Electrical simulation has been used to investigate the main differences between BiCMOS and CMOS circuits. It is shown that, because of the large driving capability of BJTs, the detection of bridging faults in BiCMOS circuits is more difficult than in the CMOS case when functional or delay testing is used whereas it becomes more effective when adopting current monitoring     

Parametric analysis of runway stone lofting mechanisms

The influence of various factors affecting the severity of runway debris lofting mechanisms was investigated by performing numerical simulations and drop-weight impact experiments to assess the likelihood of a stone impact. Geometrical characterisation of stones collected from airfields led to a generic model of a tyre rolling over stones of various shape with different overlaps, orientations, and densities. In numerical simulations of a 0.4 m diameter aircraft tyre rolling at 70 m/s, a 10 mm diameter spherical stone was lofted at a maximum vertical speed of 35 m/s. For equivalent mass prolate spheroid stones, the loft speeds were 11–34% lower depending on the stone orientation. Objects with flat surfaces exhibited different lofting mechanisms and lower angular velocities. The conditions most conducive to stone lofting were very stiff, small diameter, sharp cornered tyres rolling on ground with a high friction coefficient over spherical stones such that just under half the stone diameter was covered by the tyre. The stone loft speed was approximately proportional to the square root of the tyre tread stiffness. Finally, tyre tread grooves could throw stones upwards at the tyre-ground separation speed, which was 17 m/s for the conditions mentioned earlier.     

Enhancement of the Magnetic Coupling in Exfoliated CrCl3 Crystals Observed by Low-Temperature Magnetic Force Microscopy and X-ray Magnetic Circular Dichroism

Magnetic crystals formed by 2D layers interacting by weak van der Waals forces are currently a hot research topic. When these crystals are thinned to nanometric size, they can manifest strikingly different magnetic behavior compared to the bulk form. This can be the result of, for example, quantum electronic confinement effects, the presence of defects, or pinning of the crystallographic structure in metastable phases induced by the exfoliation process. In this work, an investigation of the magnetism of micromechanically cleaved CrCl₃ flakes with thickness >10 nm is performed. These flakes are characterized by superconducting quantum interference device magnetometry, surface-sensitive X-ray magnetic circular dichroism, and spatially resolved magnetic force microscopy. The results highlight an enhancement of the CrCl₃ antiferromagnetic interlayer interaction that appears to be independent of the flake size when the thickness is tens of nanometers. The estimated exchange field is 9 kOe, representing an increase of ≈900% compared to the one of the bulk crystals. This effect can be attributed to the pinning of the high-temperature monoclinic structure, as recently suggested by polarized Raman spectroscopy investigations in thin (8–35 nm) CrCl₃ flakes.     

Effect of biological and chemical oxidation on the removal of estrogenic compounds (NP and BPA) from wastewater: an integrated assessment procedure

A major source of the wide presence of EDCs (Endocrine Disrupting Compounds) in water bodies is represented by direct/indirect discharge of sewage. Recent scientific literature reports data about their trace concentration in water, sediments and aquatic organisms, as well as removal efficiencies of different wastewater treatment schemes. Despite the availability of a huge amount of data, some doubts still persist due to the difficulty in evaluating synergistic effects of trace pollutants in complex matrices. In this paper, an integrated assessment procedure was used, based on chemical and biological analyses, in order to compare the performance of two full scale biological wastewater treatment plants (either equipped with conventional settling tanks or with an ultrafiltration membrane unit) and tertiary ozonation (pilot scale).Nonylphenol and bisphenol A were chosen as model EDCs, together with the parent compounds mono- and di-ethoxylated nonylphenol (quantified by means of GC-MS). Water estrogenic activity was evaluated by applying the human breast cancer MCF-7 based reporter gene assay. Process parameters (e.g., sludge age, temperature) and conventional pollutants (e.g., COD, suspended solids) were also measured during monitoring campaigns.Conventional activated sludge achieved satisfactory removal of both analytes and estrogenicity. A further reduction of biological activity was exerted by MBR (Membrane Biological Reactor) as well as ozonation; the latter contributed also to decrease EDC concentrations.     

Phosphates and ammonia recovery from secondary effluents by selective ion exchange with production of a slow-release fertilizer

A process for the reduction of eutrophic potential in urban secondary effluents. which comprises the selective exchange of phosphates on a weak anion resin and of ammonia on clinoptilolite, is described. Sodium chloride is used to regenerate both resins, with some Ca(OH)₂ added for clinoptilolite. By adding Mg(OH)₂, eventually precipitated with lime from sea water, the premium quality, slow-release fertilizer MgNH₄PO₄-6H₂O is recovered from the concentrated regeneration streams, which can then be recycled. Laboratory evaluations of the hydrolysis extent of the weak anion resin in the presence of bicarbonates showed that a steady-state is attained with resin exchange capacity reproducibly averaging about 80 mmol phosphates 1,⁻. The preliminary runs on a pilot plant for the tertiary treatment of urban sewage are also presented.     

A procedure for the computation of accurate PWL approximations of non‐linear dynamical systems

In this paper we propose a variational method to find out piecewise‐linear (PWL) approximations of non‐linear dynamical systems in view of their circuit implementations. The method is based on some significant trajectories of the dynamical system and provides reasonably accurate PWL approximations with a relatively low number of parameters. The effectiveness of the method is validated by applying it to the approximation of limit cycles (both stable and unstable) in the Bautin system. Copyright © 2006 John Wiley & Sons, Ltd.     

Calcium phosphate-based nanosystems for advanced targeted nanomedicine

Synthetic calcium phosphates (CaPs) are the most widely accepted bioceramics for the repair and reconstruction of bone tissue defects. The recent advancements in materials science have prompted a rapid progress in the preparation of CaPs with nanometric dimensions, tailored surface characteristics, and colloidal stability opening new perspectives in their use for applications not strictly related to bone. In particular, the employment of CaPs nanoparticles as carriers of therapeutic and imaging agents has recently raised great interest in nanomedicine. CaPs nanoparticles, as well as other kinds of nanoparticles, can be engineered to specifically target the site of the disease (cells or organs), thus minimizing their dispersion in the body and undesired organism-nanoparticles interactions. The most promising and efficient approach to improve their specificity is the ‘active targeting’, where nanoparticles are conjugated with a targeting moiety able to recognize and bind with high efficacy and selectivity to receptors that are highly expressed only in the therapeutic site. The aim of this review is to give an overview on advanced targeted nanomedicine with a focus on the most recent reports on CaP nanoparticles-based systems, specifically designed for the active targeting. The distinctive characteristics of CaP nanoparticles with respect to the other kinds of nanomaterials used in nanomedicine are also discussed.     

Multi-agent quality of experience control

International Journal of Control, Automation and Systems - In the framework of the Future Internet, the aim of the Quality of Experience (QoE) Control functionalities is to track the personalized...     

Evaluation of decay photocurrent measurements in dye‐sensitized solar cells: Application to laser beam‐induced current technique

The use of the laser beam‐induced current (LBIC) technique in photovoltaic devices is widespread, but its use in photoelectrochemical cells, such as dye‐sensitized solar cells (DSSCs), is limited due to the configuration of these devices. The main reason is the very slow response time of DSSCs in the decay process, and therefore LBIC scans take too long to perform. We have designed a procedure published in the literature to correct the photocurrent values obtained by the LBIC technique, based on an algorithm that uses a decreasing mono‐exponential model. This work presents a study of the decay measurements in DSSCs using several functions, in order to improve the algorithm designed. It concludes that functions such as a decreasing bi‐exponential or Becquerel function generate better fits to experimental data. Copyright © 2010 John Wiley & Sons, Ltd.     

Experimental Evaluation of Thermal Properties of Grouting Materials

This study is aimed at the thermal analysis of sealant mortar （usually a mixtures of bentonite and cemem with addition of sand） used in geothermal cooling and heating. In particular, thermal conductivity and diffusivity measurements were performed on differem sealant mixtures by using Hot Disk thermal constants analyzer in order to identify the interesting thermal properties of grouting materials. The grouting materials that we considered are of porous nature and, if used in the presence of groundwater, have different levels of imbibitions. It is important to know the thermal behavior of these materials at different water content. A first set of measurements was performed on a not-tinted material at room temperature; then the samples were led to saturation conditions by contact capillary imbibitions with a cotton wool layer moistened in water. The determination of thermal conductivity in these test conditions appears to be critical compared to the measuremems on non-timed sample. The thermal conductivity tests have revealed how the thermal behavior of the samples analyzed is essentially determined by the density and water content of the material： in fact, the thermal conductivity increases of two to three times the value of the not-tinted material.