In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

石油系油浆与煤系闪蒸油的焦化性能——I．热解条件的影响

通过偏光显微镜观察了石油系油浆（LH）与煤系闪蒸油（SN）焦化后所得焦块的光学结构。结果表明，在较宽条件下两种原料单独焦化均得不到取向度高的流线型结构。将两种原料以一定比例混合后先热解丙焦化所得焦块的光学结构明显好于二者混合后直接焦化所得焦块的光学结构，其中LH和SN以3：2的重量比混合后在440℃、1MPa下热解3．5h然后再在530℃、1MPa下焦化8h所得焦块为具有较高取向度的流线型结构，适合于作为针状焦的起始原料。     

Glass fiber-filled thermoplastics. I. Wall and processing effects on rheological properties

A systematic study of wall effects on the shear viscosity of short glass fiber-filled polypropylene and polystyrene is presented. The dependence of these effects on capillary radius, shear rate, temperature, and polymer matrix is examined. The “true” viscosity curves of these materials (free from wall effects) can be obtained by an extrapolation procedure. Breakage of glass fibers in the high shear-rate processes of extrusion and injection molding lead to an appreciable reduction of the viscosity of these materials and is probably the more important effect to take into account in these processes.     

土壤固化剂无侧限抗压强度试验研究

针对山西省长治市石子河河道处理问题 ,采用固化剂粘土进行了无侧限抗压强度试验 ,并与水泥土进行了比较。发现固化剂 2的无侧限抗压试验强度最佳 ,为工地现场试验及河道综合治理提供了更为有力的理论依据     

软硬件协同设计语言System C在SoC设计中的应用

软硬件协同设计是未来VLSI设计的发展趋势.作为新的系统级VLSI设计标准,System C是一种通过类对象扩展的基于C/C++建模平台,支持系统级软硬件协同设计、仿真和验证.文章讨论了SystemC复杂芯片设计中的设计流程、设计优势,并给出具体设计实例.     

低压宽温高频铝电解电容器工作电解液

在传统的己二酸铵/乙二醇加水体系中,通过增加水的含量实现高电导率,同时在电解液中添加多种有机高分子物质形成复合添加剂,改善工作电解液的高温稳定性,使电容器上限工作温度扩展到105℃,形成高频宽温低阻抗工作电解液。     

彩色显像管电子束亮度分布自动测量系统

电子束轮廓的描述是彩色显像管特性检测中的难点之一。采用光电转换与计算机信息处理技术，通过自动调整边界条件和三次样条拟合的方法建立了电子束轮廓自动测量系统。与传统测量方法相比，该系统精度高，测试速度快，极大地减轻了测试人员的工作强度，并增加了对排列率和并列率等的测试功能。     

Electrical Resistance Measurement of Glass Transition and Crystallization Characteristics of Zr—Al—Cu—Ni Metallic Glasses

In this paper,glass transition and thermal stability of the Zr-Al-Cu-Ni metallic glasses were investigated by using electrical resistance measurement(ERM),DSC and X-ray diffraction techniques.The experimental results show that the ERM is capable of detecting the glass transition of the amorphous alloys and can help to distinguish the crystallization products of the Zr-Al-Cu-Ni metallic glasses owing to the difference of the electrical resistivity between the precipitation phases.     

近非临界相位匹配温度调谐MgO：LiNbO3OPO

通过对MgO:LiNbO3参量过程温度相位匹配及走离角，允许参量等运转参数的理论计算与分析，确定了晶体的切割角度θ=82℃，以近非临界相位匹配（NCPM）取代NCPM，将温度调节范围控制在较低的温度上，研制了532nm泵浦的MgO:LiNbO3温度调谐脉冲光学参数振荡器（OPO），在800～1700nm波段实现连续调谐输出。参量泵浦功率密度阈值为57.3MW/cm^2，泵浦能量约2倍阈值处，单谐振（SRO）参量转换效率为11%以上。     

心脏黏液瘤的超微结构研究

对8例心脏黏液瘤进行了临床病理总结，着重进行了超微结构的研究，结果表明黏液瘤细胞有4种超微结构表现：（1）原始间叶细胞；（2）纤维母细胞样；（3）肌纤维母细胞样；（4）上皮样。提出心脏黏液瘤细胞起源于原始间叶细胞，有纤维母细胞、肌及上皮样分化。并且提出瘤细胞参与黏液瘤基质的形成。