Study on the dispersion characteristic of the plasma-loaded relativistic BWO

The dispersion characteristic of the plasma-loaded relativistic backward wave oscillator has been analyzed. The theoretical model has been established and the numerical calculations accord with the experimental results, which provides some useful suggestions on the designing of slow-wave structure of BWO.     

Al,Ga取代Bi：DyIG薄膜的磁和磁光特性的研究

本文报道用热分解法在玻璃衬底上制备了Ａｌ和Ｇａ取代的Ｂｉ：ＤＹＩＧ薄膜，对其磁和磁光特性做了详细研究．Ａｌ和Ｇａ取代的薄膜均可获得好的矩形比和高的矫顽力．对于Ｂｉ１．２Ｄｙ１．８Ｆｅ５－ｘＭＸＯ１２（Ｍ＝Ａ１，ＧＺ）薄膜，Ａ１和Ｇ２的最佳替代成份分别为１．０和Ｇ．７；最佳晶化温度分别为７００ｏ℃和６７５℃．在波长５１０ｎｍ附近，法拉第旋转角可达８°／ｕｍ左右．光学吸收和品质因子的研究结果表明，Ａｌ和Ｇａ取代能够影响光学吸收和品质因子，其中Ｇａ取代对光学吸收和品质因子的影响较大．     

气—液式热管换热器在硫酸工业中的应用研究

本文研制的气－液式热管换热器应用于硫酸生产中ＳＯ３气体的余热回收。它具有传热性能好、流动阻力小、寿命长、体积小、节能效果显著和易清垢等优点。     

变结构变参数设计方法及其在机械CAD中的应用

提出了一种新颖的机械结构设计思想－变结构变参数设计方法，并结合实例，阐述了变结构变参数设计的概念、原则、实施措施和意义。由此对Ｉ－ｄｅａｓ软件包进行了二次开发，编制了发动机曲轴专用ＣＡＤ软件程序，并用某型号发动机曲轴进行了验证。     

Preparation of Metal-Coated Carbon Fiber Reinforced Composites and Their Electromagnetic Properties

Medium temperature curing by infrared radiation was used to prepare electromagnetic wave absorbing multilayered plastic matrix composite materials containing metal-coated carbon fibers (MCFs). The electromagnetic properties of the materials were investigated by frequency scanning tests with microwave vector network analyzer. It is found that the electromagnetic parameters, mainly permittivity of the composites increase significantly with the addition of MCFs, which gives the composites good designability as thin, light-weight EM wave absorbers. It is also shown that MCFs can improve on the EM wave energy attenuating property of the composites by widening the work frequency band width and raising the absorptive peak     

Assessment model of dam operation risk based on monitoring data

Although the dams produce remarkable social and economic benefits, the threat made by unsafe dams to the life and property of people who live in the lower river area is un-negligible. Based on the monitoring data which reflect the safety condition of dams, the risk degree concept is proposed and the analysis system and model for evaluating risk degree (rate) are established in this paper by combining the reliability theory and field monitoring data. The analysis method for risk degree is presented based on Bayesian approach. A five-grade risk degree system for dam operation risk and corresponding risk degree is put forward according to the safety condition of dams. The operation risks of four cascade dams on some river are analyzed by the model and approach presented here and the result is adopted by the owner.     

西北江三角洲来水来沙的非线性分形特征

根据西、北江干流高要、石角及西北江三角洲网河区顶点马口、三水四个水文站的流量和含沙量资料 ,应用非线性分形原理的R S方法 ,计算西北江干流及西北江网河区顶点四个水文站的流量、含沙量的赫斯特数H和分形维数D ;探讨西、北江干流来水来沙的分形特征及西北江三角洲的分水分沙规律。结果表明 ,流量的分维数略大于含沙量的分维数 ,三水站流量及含沙量的分维数与其上游的石角站流量、含沙量的分维数相差较大 ,与思贤的分水分沙造成西北江的水沙交换有关     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

化学锚固在结构改造加固中的应用

随着钢筋混凝土结构技术的日趋成熟,一项新兴的技术逐渐被人们认同和重视,即钢筋混凝土结构改造中的化学锚固技术。早在20世纪六七十年代,发达国家已经研制出利用化学栓剂,将螺栓、钢筋种植在混凝土结构中,特别是对于既有混凝土结构改造及加固起到了决定性的作用。随着改革开放,这项技术在我国也逐步得到了运用。1各种结构胶在工程中的应用结构胶的应用范围非常广泛,就锚固来讲,解决了新旧混凝土之间钢筋连接及新旧结构间应力的传递。如某博物馆结构改造中原结构为框架结构,始建于20世纪50年代末期,经鉴定不符合烈度为8度的抗震要求,现将其…