CDMA发射分集系统的多用户检测常模算法分析

空时分集技术的最大优点在于在不增加带宽的情况下可以提高系统的可靠性,是目前移动通信的研究热点.常模算法是一种性能优良的码分多址(CDMA)盲多用户检测技术,能确保判决信号与实际传送信号之间的差错较小,误码率性能良好.文中提出将标准线性受限常模算法(LCCMA)与空时分组码(STBC)相结合,设计出一种收敛快、能够改善系统性能的基于2-空时分组码的多用户接收机.     

Experimental Research on Erbium-doped Superfluorescent Fiber Source

The effects of the variations in fiber length, fiber mirror reflectance on efficiency and output power are experimentally investigated for erbium-doped double pass backward superfluorescent fiber sources (SFSs). The influence of fiber length on mean wavelength stability (MWS) has also been demonstrated. By incorporating a short section of un-pumped erbium-doped fiber (EDF) at the output port, the pump power dependent on MWS becomes independent of pumped EDF length. This is a novel phenomenon that hasn‘t been reported up to now,and should be helpful to SFS fabrication and theory analysis. By using a fiber Michelson interferometer as spectrum slicing component,a multi-wavelength fiber source (MWFS) with ～20 channels (from 1542nm to 1559nm) is got. The MWFS has a channel spacing of ～0. 8 nm which satisfies ITUstandard. The intensity fluctuation among channels is less than 0.5dB,and the extinction ratio of all channels is above 14dB. This kind of MWFS should be useful to wavelength division multiplexing systems.     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

项目管理软件的开发思路

详细介绍了项目管理的发展及项目管理软件的现状。通过对P3管理软件的分析论述，得出项目管理软件系统的开发方案。     

逆向反射镜光度测量

为了正确评价逆向反射镜的加工质量与使用效果，且将二者有机地统一起来，本文提出应根据测试目的来选择合适的光度测量方法，并进一步分析了不同测试目的将导致测量装置的组成、几何条件（距离，孔径角，工作姿态等）、光度条件（光源色温、稳定性与均匀性，接收器线性、灵敏度与光谱修正等）、测量参数（反光强度系数、逆反射系数、逆亮度系数等）等各不相同。     

Carbon Nanotubes Grown on the Surface of Cathode Deposit by Arc Discharge

Carbon nanotubes prepared by de arc discharge of graphite electrodes in He and CH₄ gas took markedly different morphology. Thick nanotubes embellished with many carbon nanoparticles were obtained by evaporation under high CH₄ gas pressure and high arc current. Thin and long carbon nanotubes were obtained under a CH₄ gas pressure of 50Torr and an arc current of 20A for the anode with a diameter of 6mm.     

WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。