D2000-22型煤气鼓风机的振动原因分析及改善

针对D2000--22型煤气鼓风机的结构特点及工作原理，对产生机械振动原因进行了分析，并提出改善措施。     

难熔金属与硬质材料进展─—从第十三届国际普兰西会议看发展动向（Ⅰ）

根据第十三届国际普兰西会议获得的信息，对国际上难熔金属、硬质合金、硬质材料和涂层技术等方面近几年来的研究和发展动态进行了综合评述。最后，提出了几点自己的看法。     

四川盆地中部上三叠统香溪群岩性油气藏圈闭类型及其特征

四川盆地川中地区构造平缓,大型断裂欠发育,已发现的油气藏与背斜关系并不十分密切。研究认为,川中地区香溪群主要发育岩性圈闭,根据圈闭形成主控因素,结合香溪群沉积前的古地貌特征和裂缝发育特点,将川中香溪群岩性圈闭划分为4种类型:①与地层尖灭相关的地层—岩性圈闭;②与沉积—成岩相变密切相关的成岩—岩性圈闭;③与古地貌有关的差异压实作用形成的岩性圈闭;④与断层转化调节相关的裂缝—岩性复合圈闭。其中成岩—岩性圈闭和地层—岩性圈闭,是川中香溪群最重要的、分布最广泛的圈闭类型。     

The chemical anchoring of noble metal amine precursors to silica

The effect of pretreatment on the dispersion of supported noble metal Catalyst prepared from amine precursors in basic solution have been studied. The following metal precursors were used: Pt(NH₃)₄(NO₃)₂, Pd(NH₃)₄(NO₃)₂, Ru(NH₃)₆Cl₃ and [Rh(NH₃)₅Cl]Cl₂ Pretreatment in oxygen, prior to reduction in H₂ at 400C, resulted in poor dispersions for Ru and Rh, moderate dispersions for Pd and high dispersions for Pt. Pretreatment in H₂ resulted in poor dispersions for Pd and Pt and high dispersions for Ru and Rh. Decomposition of the adsorbed Pt and Pd precursors in argon resulted in very high dispersions.     

27keV Ar~+斜入射时的Cu-Au合金溅射实验角分布

用27keV Ar~+分别在垂直和倾斜入射情况下,轰击了Cu-Au(30wt％)合金样品,测量了Cu和Au原子的溅射角分布。角分布是用卢瑟福背散射(RBS)技术分析Al捕获膜上的Cu-Au沉积成分而定量得到的。结果表明:(1)在Ar~+倾斜(θ=40°)入射时,Cu原子择优发射,且程度比垂直入射(θ_r=O°)时增强:(2)倾斜入射时,Cu原子的角分布显示出在接近于样品表面法线方向的发射角范围内(θ<45°),发射机率比垂直入射时减小。     

Boussinesq方程的永形波的级数解

对于用层平均速度势(或速度)与波高给出的非线性等水深Boussinesq方程,与KdV方程一样,存在两类永形波—孤立波和周期波。不同的是,对于Boussinesq方程,孤立波和周期波一样,是以反函数的积分形式给出的,这在使用上是不方便的。本文对这两类波,分别给出了相应的级数形式的正函数解。对于孤立波,级数的收敛速度是十分快的,且文中还给出了一个具有高精度的十分简单的近似解,对于周期波,只要有关参数选得合适,解的收敛速度也是相当快的。这就有效地克服了反函数形式解在使用上的不方便。     

C－BN衬底上金刚石的异质外延生长研究

用热灯丝ＣＶＤ方法在Ｃ－ＢＮ单晶衬底上制备出金刚石膜，并且在Ｃ－ＢＮ（１００）面上观察到金刚石的异质外延。     

Constraint-based beautification and dimensioning of 3D polyhedral models reconstructed from 2D sketches

3D models reconstructed from 2D sketches are inaccurate because of the inherent inaccuracies in the input and the reconstruction method. It is therefore necessary to “beautify” them before use in CAD systems. We present a method that detects geometric constraints, such as parallel and orthogonal faces, present in the reconstructed model and then selects a subset that constrains the object sufficiently and consistently. The subset selection algorithm first prioritizes the constraints depending on their type and then uses a novel method, based on quasi-Newton optimization, to detect and eliminate redundant and inconsistent constraints. The remaining constraints then define the dimensions of the model fully and consistently. Results from our implementation show that the method can beautify and dimension recovered 3D models correctly at acceptable speed.