A comparison of commonly used hydrologic design methods for rainwater collectors

Rainwater collection as a possible water source in developing countries is introduced. The major parameters in calculating the size of the tank are defined. Six methods that have been used previously to relate demand, storage, reliability and the rainfall pattern are compared to the Ottawa Model over a wide range of demands.     

The advancing-front mesh generation method revisited

This paper presents a mesh generation method of the advancing-front type which is designed in such a way that the well-known difficulties of the classical advancing-front method are not present. The retained solution consists of using the first steps of a Voronoï–Delaunay method to construct a background mesh which is then used to govern the algorithm. The two-dimensional case is considered in detail and possible extensions to adaption problems and three dimensions are indicated.     

The case of Gary: In search of post-hoc quixotic flexibility.

Responds to M. F. Hoyt's (see record 1995-22250-001) commentary on T. F. Van Denburg and E. J. Van Denburg's (see record 1994-18427-001) response to Hoyt's (see record 1994-18395-001) commentary on Van Denburg and Van Denburg's (see record 1993-06526-001) article about a case of premature therapy termination. Issues related to limits and flexibility in treatment are addressed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Dislocations and flux pinning in YBa2Cu3O7

The dislocation structures of bulk textured and epitaxial thin film YBa₂Cu₃O₇ superconductors are examined. Correlations between increases in flux pinning and dislocation densities are noted. A model for flux pinning by individual dislocations is presented. This gives a treatment of strain induced effects and effects of normal state region interactions. It is shown that the values of pinning predicted are in line with experimental observations.     

Wide- and narrow-band bandpass coplanar filters in the W-frequency band

This paper deals with the design of passive coplanar devices in the W-frequency band. As long as coplanar transmission lines are correctly dimensioned, analytical models based on quasi-TEM approximation can be used. Such models are associated with a correct definition of the reference planes at the junctions and employed for junction discontinuities, T- and cross-junctions. In order to validate these assertions, simulated and experimental data on classical quarter-wavelength shunt-stub filters are first presented. Then the design of traditional coupled-line filters is examined. The problems in terms of insertion loss associated with these kinds of narrow-band applications are discussed here. Minimization of insertion losses requires increasing the width of the strips. Consequently, the design becomes complex and modeling using transmission-line models less accurate. Nevertheless, as an optimization procedure is needed to tune the filter theoretically, such a very fast design method is necessary. Simulated and experimental results in the range 500 MHz to 110 GHz are compared throughout the paper.     

The influence of packaging materials on RF performance

At frequencies beyond 1 GHz, every component of the IC package contributes to the RF performance, whether required or not. In this work, we study the effects of packaging materials namely, the substrate and the globtop/underfill material on RF performance. We have measured interconnects on two area-array CSPs, the ball grid array and the polymer stud grid array using IMEC’s MCM-D technology. The measurements on the package interconnect show that the losses in the package substrate material account for about 50% of the total losses at 1.8 GHz and this drops to less than 20% at 5.2 GHz. The losses due to impedance mismatch dominate the losses especially below 10 GHz and considerable improvement in performance cannot be obtained by using an improved/expensive substrate. The other study is about the influence of globtop/underfill materials on wirebonds (through 3D EM simulations) as well as on standard 50 Ω MCM-D transmission lines (through experiments). While a higher value of dielectric constant of the globtop/underfill material is better on wirebonds, the influence of loss tangent is felt only above values of 0.1. The influence of seven different globtop/undefill materials on 50 Ω transmission lines has been used to extract their dielectric constant and loss tangent values at 30 GHz. These results are very valuable since one can hardly find the properties of globtop/underfill materials beyond 1 GHz.     

Ultraviolet chambers based on integrating spheres for use in artificial weathering

Laboratory ultraviolet (UV) chambers are widely used to obtain weathering data for a wide range of commercial polymer products including coatings, textiles, elastomers, plastics, and polymeric composites. Although numerous improvements have been made in the design of UV chambers over the last 80 years, the reproducibility of the exposure results from these chambers has remained elusive. This lack of reproducibility is attributed to systematic errors in their design, operation, and control which prevent direct comparisons of the performance of materials exposed in the same environment, comparisons of the performance of the same material exposed in different laboratories, and the comparison of field and laboratory results. This paper describes an innovative UV chamber design based on integrating sphere technology that greatly reduces the magnitude of these errors, as well as provides additional experimental capabilities. Presented at the 79th Annual Meeting of the Federation of Societies for Coatings Technology, on November 4–7, 2001, in Atlanta, GA. Building Materials Division. Gaithersburg, MD. Freeport, TX.