基于安全操作系统的透明加密文件系统的设计

1 引言随着Internet的飞速发展,信息资源的共享程度进一步加强,随之而来的信息安全问题也日益突出。但是现在的系统越来越复杂,系统中总是存在着各种各样的漏洞,以及一些人为的因素(如:没有合理配置防护墙规则,口令比较弱等)。这些都有可能被黑客利用,入侵到系统中去。     

OSOD:一个油田开发规划优化决策系统

油田开发规划是一项复杂的系统工程,在一定投资下,要使得利润最大、产量最大,并且尽量降低成本,需要通过数学规划的方法进行科学合理的决策。为此,该文开发了油田开发规划优化决策系统,可以作为长期或短期油田开发规划的决策工具。     

基于Pocket PC的分布式程序设计

本文介绍了实现Pocket PC与PC之间的分布式程序设计的原理．并用实例详细介绍了进行分布式程序设计的主要方法。     

化学转化柱法测定气体中的微痕量水分的气敏分析仪的研究

采用特制LiAlH4催化反应柱,在(40～60)0C下,将气体中的微、痕量水转化成氢气.以气体中的微、痕量氢标准样品为标准,利用N型二氧化锡气敏半导体传感器作为检测器的气敏色谱方法,通过对转化的氢气进行准确测定,从而间接得出气体中微、痕量水的含量.研究表明,本文设计的催化反应装置选择性好,常温下反应快速、完全且稳定,一年来进行了近3000次试验考察表明,转化效率基本保持稳定,数据重复性很好.同时,气敏色谱法测水干扰因素少,进样量少,仅(1～2)ml,样品消耗少,仅(2～5)升,几分钟即可完成分析.该方法由于有微量氢标准气体作为相对标准,测水准确度高,不确定度为1%～10%.     

Tribological performance of filled PTFE‐based friction material for ultrasonic motor under different temperature and vacuum degrees

In this work, a glass fiber reinforced polytetrafluoroethylene (PTFE)‐based friction material with good properties for ultrasonic motor was fabricated. The effects of temperature and vacuum degree on the tribological behavior of the PTFE‐based friction material were investigated; the evolutions of friction‐wear modes and mechanisms were also discussed as function of temperature and vacuum degree. The results show that the delamination and fatigue wear are predominant under the effects of repeated shearing and dynamic contact under atmospheric environment. While wear mechanisms change from adhesive to abrasive and fatigue wear as it is cooled from 30 to ?60 °C at vacuum environment. Under high vacuum, adhesive wear was prone to taking place at room temperature for high frictional heat which increased the wear rate and extended the running‐in period. Experiment shows that the highest no‐load speed, output power, and holding torque of ultrasonic motor at room temperature under atmospheric environment are 220 rpm, 9.9 W, and 1.21 N m, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45358.     

Effect of initial gas pressure on the reaction of Al with water

The effect of initial gas pressure on Al–water reaction was investigated systematically. It was found that there is a non-monotonic relationship between the initial pressure and the induction time for the beginning of Al–water reaction. The induction time decreases with decreasing the initial pressure at the first stage from atmospheric pressure, then reaches a minimum, and finally increases with further decreasing the initial pressure. The mechanism analyses revealed that the special vacuum pressure corresponding to the minimum induction time is close to the saturated vapor pressure, below which probably there are some vapor bubbles passing or adsorbing on Al particle surfaces due to boiling, retarding the hydration process of Al surface oxide film and increasing the reaction induction time. The present results imply that a suitable initial gas pressure should be chosen for Al–water reaction to generate hydrogen.     

影响自洁玻璃光催化性能的热处理工艺研究

通过介绍自清洁玻璃产生的背景,阐述自洁玻璃的自清洁原理。从TiO_2薄膜的微观结构入手分析了TiO_2晶型对光催化性能的影响,从而找到相对应晶型的热处理工艺。     

一种评价油水井生产能力的新方法及其应用研究

准确认识和评价油水井生产能力,是油田进行合理配产配注和开发调整的基本依据。在综合分析油水井基本产能公式和实际生产动态变化的基础上,建立了累积产液量、注入量与生产压差积分的关系,并用综合产液指数、综合吸水指数,来反映油水井的实际生产能力;而在实际生产过程中,开采条件变化产生的影响可以直观地反映在不同阶段油水井的生产能力变化上,通过计算不同阶段的综合产液指数、综合吸水指数,可以准确分析和评价不同开发阶段、不同条件下,油水井综合生产能力和变化趋势。实例应用表明,利用本文建立的方法,计算过程简捷、分析结果准确,可以为油藏开发调整和油井措施的实施奠定基础。     

铝合金激光-MIG复合焊接头性能研究

探讨了激光与电弧相互作用后,焊缝中心上部和下部晶粒大小不同的原因,在此基础上研究了焊接速度的改变对6009铝合金接头的微观组织、拉伸性能、显微硬度的影响。结果表明：6009铝合金激光-MIG焊焊接接头的抗拉强度和延伸率随着焊接速度的增加而增加,拉伸试样的断裂位置由焊缝区转移到热影响区,断口呈现均匀分布的韧窝形貌,断裂机制为微孔聚集形断裂;焊缝中心上部晶粒小于焊缝中心下部,而且尺寸分布均匀。焊缝中心上部的显微硬度则高于焊缝下部。接头热影响区存在软化区,宽度为4～6 mm。