Monitoring fuel quality: a case study for quinizarin marker content of unleaded petrol marketed in Greece

Fuel adulteration and cross-contamination lead to low-quality fuel products, which may cause increased environmental pollution, loss of taxes and engine problems. An establishment of a quality monitoring mechanism based on laboratory measurements may reveal problematic areas of the fuel supply chain. For the purposes of this work, 97 unleaded petrol samples were measured in order to quantify mass concentration of quinizarin, a substance used in Greece to easily mark the presence of 95 Research Octane Number unleaded petrol in other types of automotive fuels. The samples were obtained from petroleum retail stations selling different brands of fuels and located in different geographic regions of Greece. Statistical analysis of the results revealed quinizarin mass concentrations below the 3 mg L^?1 legislation specification limit and significant differences between brands and geographic regions, which may attributed to the structure of the fuel supply chain in Greece in combination with quinizarin properties and way of handling. Moreover, certain approaches were used for the calculation of decision limits for assessing compliance or non-compliance. These approaches take measurement reproducibility or estimated in-house uncertainty into account, in order to minimize the probability of false rejection.     

Reaction to Paul’s Column “Where do we find the graphs from PT programmes showing measurement performance?”

The tentative arguments mentioned by Paul De Bievre are discussed and alternatives are given that may lead to different insights.     

Validation of primary formaldehyde gas standards prepared by dynamic thermogravimetry through a tri-national comparison of gaseous formaldehyde amount fraction

A validation study for primary formaldehyde gas standards was performed at three National Metrology Institutes: the Korea Research Institute of Standards and Science (KRISS), the National Metrology Institute of Japan (NMIJ) and the National Institute of Metrology of China (NIM). The studied materials had a nominal amount fraction of 2 μmol/mol formaldehyde in nitrogen balance and were prepared in 10-L aluminum cylinders by KRISS. The impurities in the materials were analyzed using a gas chromatograph/atomic emission detector and a Fourier-transform infrared spectrometer (FTIR). The stability of the materials was assessed for 1 year by KRISS using paraformaldehyde as a source for the primary standard gas and a cavity ring-down spectrometer (CRDS) instrument as the measurement method. The amount fraction of formaldehyde in the materials decreased linearly by 0.74 % each month. The studied materials that exhibited similar linear rates of decline were distributed to the participants. After the measurement was completed by the participants, the materials were returned to KRISS and the stability analysis based on the primary standard maintained at KRISS was repeated. NMIJ analyzed the materials using paraformaldehyde as the source of the primary standard of formaldehyde and FTIR analysis, whereas NIM used trioxane as the primary standard gas source and CRDS analysis. The results of the comparison revealed good agreement between the results and were within the expanded uncertainty of 2 % although each of them used different combinations of methods in the generation of primary gas standards and measurements.     

Comparison of standard addition and conventional isotope dilution mass spectrometry for the quantification of endogenous progesterone in milk

In this study, a standard addition–isotope dilution mass spectrometry (SA-IDMS) method for quantification of endogenous progesterone in milk has been described. The method validation results, linearity, limits of detection and quantification, recovery and uncertainty were fit for the purpose of assigning reference mass fractions to proficiency testing schemes. The developed technique was compared to the isotope dilution mass spectrometry (IDMS) method already existing in the laboratory. Analytical results of two milk samples were (1.377 ± 0.048) μg/kg and (4.457 ± 0.155) μg/kg by SA-ID-LC/MS method, while the results were (1.355 ± 0.019) μg/kg and (4.359 ± 0.059) μg/kg by ID-LC/MS, respectively. Since SA-IDMS was an effective quantitative method that overcame matrix effect, similar quantitative results from IDMS and SA-IDMS indicated that the quantification of progesterone in milk was barely influenced by matrix. Both IDMS and SA-IDMS could be used to assign reference mass fractions to progesterone in milk inter-laboratory proficiency testing schemes.     

Glutaraldehyde crosslinking of arabinoxylan produced from corn ethanol residuals

This study investigated the possibility of substituting petroleum-based polymers with biopolymers for films and paper coatings. Arabinoxylan (AX) was extracted from distillers’ grains, a low-value corn ethanol byproduct, and modified through crosslinking with glutaraldehyde (GA) which was made into films and paper coatings. The effects of degree of substitution (DS) on film and coating properties of GA cross-linked AX, referred to as GAX, were investigated. The GAX films had markedly higher tensile strength, approximately 3 times higher than the unmodified AX films at low DS, with higher DS causing a negative effect on the film tensile strength. Compared to unmodified AX coating, paper coated with GAX also had significantly higher tensile index, presumably due to high adhesion between the coating and paper interface. When used as a coating binder with calcium carbonate pigments, GAX showed comparable performance to polyvinyl alcohol, a common industrial binder, demonstrating the potential to be substituted for the petroleum-based paper coating binder.     

Effect of boundary representation on viscous,separated flows in a discontinuous-Galerkin Navier–Stokes solver

The effect of curved-boundary representation on the physics of the separated flow over a NACA 65(1)-412 airfoil is thoroughly investigated. A method is presented to approximate curved boundaries with a high-order discontinuous-Galerkin spectral element method for the solution of the Navier–Stokes equations. Multiblock quadrilateral element meshes are constructed with the grid generation software GridPro. The boundary of a NACA 65(1)-412 airfoil, defined by a cubic natural spline, is piecewise-approximated by isoparametric polynomial interpolants that represent the edges of boundary-fitted elements. Direct numerical simulation of the airfoil is performed on a coarse mesh and fine mesh with polynomial orders ranging from four to twelve. The accuracy of the curve fitting is investigated by comparing the flows computed on curved-sided meshes with those given by straight-sided meshes. Straight-sided meshes yield irregular wakes, whereas curved-sided meshes produce a regular Karman street wake. Straight-sided meshes also produce lower lift and higher viscous drag as compared with curved-sided meshes. When the mesh is refined by reducing the sizes of the elements, the lift decrease and viscous drag increase are less pronounced. The differences in the aerodynamic performance between the straight-sided meshes and the curved-sided meshes are concluded to be the result of artificial surface roughness introduced by the piecewise-linear boundary approximation provided by the straight-sided meshes.